tn8020 Amplifonix, tn8020 Datasheet
![no-image](/images/no-image-200.jpg)
tn8020
Manufacturer Part Number
tn8020
Description
Rf Amplifier Model Cz8020
Manufacturer
Amplifonix
Datasheet
1.TN8020.pdf
(1 pages)
16
15
14
13
12
+9
+8
+7
+6
+5
RF AMPLIFIER
MODEL
www.SpectrumMicrowave.com
Specifications
Features
! ! ! ! ! Lower Cost
! ! ! ! ! Operating Temp. 0 ºC to +70 ºC
! ! ! ! ! Environmental Screening Available
Note: Care should always be taken to effectively ground the case of each unit.
Legend
CHARACTERISTIC
Frequency
Gain (dB)
Reverse
Isolation (dB)
VSWR
Noise Figure (dB)
Power
Power @ 1 dB
Comp. (dBm)
Start kHz
Start kHz
1 dB Comp. (dBm)
Out
m A
Vdc
In
Gain (dB)
+25 ºC
kHz - 400 MHz
Ta= 25 ºC
Spectrum Microwave · 2144 Franklin Drive N.E. · Palm Bay, Florida 32905 · PH (888) 553-7531 · Fax (888) 553-7532
Spectrum Microwave (Europe) · 2707 Black Lake Place · Philadelphia, Pa. 19154 · PH (215) 464-4000 · Fax (215) 464-4001
TYPICAL
CZ8020
<1.5:1
<2.0:1
+7.0
-15
4.5
+5
14
25
Stop 400 MHz
Stop 400 MHz
+70 ºC - - - - - - 0 ºC
Ta = 0 ºC to +70 ºC
3.0
2.0
1.0
- 10
- 20
- 30
- 40
kHz - 400 MHz
0
Typical Performance Data
2.5:1 Max.
2.5:1 Max.
MIN/MAX
Start kHz
Start kHz
+5.0 Min.
-14 Max.
6.0 Max.
28 Max.
13 Min.
+5
Reverse Isolation (dB)
Input VSWR
Typical Intermodulation Performance at 25 º C
Second Order Harmonic Intercept Point ....... +32 dBm (Typ.)
Second Order Two Tone Intercept Point ........ +26 dBm (Typ.)
Third Order Two Tone Intercept Point ............ +21 dBm (Typ.)
Available as:
Maximum (No Damage) Ratings
Ambient Operating Temperature .............. -55ºC to + 100 ºC
Storage Temperature ............................... -62ºC to + 125 ºC
Case Temperature ................................................. + 125 ºC
DC Voltage ........................................................... + 8 Volts
Continuous RF Input Power ................................... + 8 dBm
Short Term RF Input Power ...... 50 Milliwatts (1 Minute Max.)
Maximum Peak Power ................... 0.5 Watt ( 3 sec Max.)
*Three external capacitors and a decoupling impedence are
required. The decoupling impedance must be large in comparison to
the 50 Ohm load to minimize gain reduction. The external capacitors
determine the low frequency response of the amplifier.
*Decoupling Impedance is 1 kOhm.
Stop 400 MHz
Stop 400 MHz
CZ8020, 3 Pin TO-39
TN8020, 4 Pin Surface Mount (SM3)
BX8020, Connectorized Housing (H1)
3.0
2.0
1.0
5
3
2
6
4
Start kHz
Start kHz
Noise Figure (dB)
Output VSWR
Stop 400 MHz
Stop 400 MHz
3/30/04