il710t-2 NVE Corp., il710t-2 Datasheet - Page 5

• Manufacturer Part Number: il710t-2
• Description: High Speed/high Temperature Digital Isolators
• Manufacturer: NVE Corp.

5 Volt Electrical Specifications
Electrical specifications are T
Notes (apply to both 3.3 V and 5 V specifications):
1.
2.
3.
4.
5.
6.
7.
8.
9.
Parameters
Input Quiescent Supply Current
Output Quiescent Supply Current
Logic Input Current
Logic High Output Voltage
Logic Low Output Voltage
Maximum Data Rate
Pulse Width
Propagation Delay Input to Output
(High to Low)
Propagation Delay Input to Output
(Low to High)
Propagation Delay Enable to Output
(High to High Impedance)
Propagation Delay Enable to Output
(Low to High Impedance)
Propagation Delay Enable to Output
(High Impedance to High)
Propagation Delay Enable to Output
(High Impedance to Low)
Pulse Width Distortion
Propagation Delay Skew
Output Rise Time (10%–90%)
Output Fall Time (10%–90%)
Common Mode Transient Immunity
(Output Logic High or Logic Low)
Dynamic Power Consumption
Power Frequency Magnetic Immunity
Pulse Magnetic Field Immunity
Damped Oscillatory Magnetic Field
Cross-axis Immunity Multiplier
IL710 and IL710S
IL710T
IL710 and IL710T
IL710S
IL710 and IL710T
IL710S
Absolute maximum ambient operating temperature means the device will not be damaged if operated under these conditions. It does not
guarantee performance.
PWD is defined as |t
t
CM
common mode input voltage that can be sustained while maintaining V
and falling common mode voltage edges.
Device is considered a two terminal device: pins 1–4 shorted and pins 5–8 shorted.
Dynamic power consumption is calculated per channel and is supplied by the channel’s input side power supply.
Minimum pulse width is the minimum value at which specified PWD is guaranteed.
The relevant test and measurement methods are given in the Electromagnetic Compatibility section on p. 6.
External magnetic field immunity is improved by this factor if the field direction is “end-to-end” rather than to “pin-to-pin” (see diagram on p. 6).
PSK
is the magnitude of the worst-case difference in t
H
is the maximum common mode voltage slew rate that can be sustained while maintaining V
(7)
(2)
PHL
(3)
− t
min
PLH
(6)
to T
(9)
|. %PWD is equal to PWD divided by pulse width.
(4)
max
unless otherwise stated.
Magnetic Field Immunity
|CM
Symbol
PWD
H
I
I
V
V
H
PW
t
t
t
t
t
t
t
H
H
K
DD1
DD2
PHL
PLH
PHZ
PZH
PSK
PLZ
PZL
t
I
t
|,|CM
OSC
OH
PM
OL
R
F
PF
I
X
L
PHL
|
Switching Specifications
and/or t
DC Specifications
0.8 x V
V
Min.
DD
2800
4000
4000
−10
100
130
10
20
PLH
−0.1
DD
(8)
between devices at 25°C.
5
(V
O
DD2
< 0.8 V. The common mode voltage slew rates apply to both rising
0.9 x V
= 5V, 3V<V
Typ.
3500
4500
4500
V
110
150
200
2.5
0.5
7.5
0.3
2.5
10
10
10
30
5
0
3
3
3
3
2
4
1
1
DD
DD
DD1
Max.
<5.5V)
340
0.1
0.8
15
10
15
15
3
6
5
5
5
5
3
3
6
3
3
O
> 0.8 V
μA/MHz
kV/μs
Units
Mbps
Mbps
A/m
A/m
A/m
mA
μA
μA
DD
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
V
V
2
. CM
L
is the maximum
Test Conditions
I
I
I
I
C
C
50% Points, V
C
C
C
C
C
C
C
C
C
C
V
50Hz/60Hz
t
0.1Hz – 1MHz
p
O
O
O
O
L
L
L
L
L
L
L
L
L
L
L
L
cm
= 8µs
= −20 μA, V
= −4 mA, V
= 20 μA, V
= 4 mA, V
= 15 pF
= 15 pF
= 15 pF
= 15 pF
= 15 pF
= 15 pF
= 15 pF
= 15 pF
= 15 pF
= 15 pF
= 15 pF
= 15 pF
= 300 V
IL710
I
I
= V
O
I
= V
I
= V
= V
IL
IL
IH
IH