mcf52221 Freescale Semiconductor, Inc, mcf52221 Datasheet - Page 34

no-image

mcf52221

Manufacturer Part Number
mcf52221
Description
Mcf52223 Coldfire Microcontroller 32-bits Microcontrollers With Usb And Zigbee
Manufacturer
Freescale Semiconductor, Inc
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
mcf52221CAE66
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Part Number:
mcf52221CAF66
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Part Number:
mcf52221CAF80
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Part Number:
mcf52221CVM66
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Electrical Characteristics
1
2
3
4
5
6
7
8
9
2.8
GPIO can be configured for certain pins of the QSPI, DDR Control, timer, UART, Interrupt
GPIO mode, the timing specification for these pins is given in
The GPIO timing is met under the following load test conditions:
34
Frequency un-LOCK range
Frequency LOCK range
CLKOUT period jitter
On-chip oscillator frequency
• Peak-to-peak (clock edge to clock edge)
• Long term (averaged over 2 ms interval)
All internal registers retain data at 0 Hz.
Depending on packaging; see
Loss of Reference Frequency is the reference frequency detected internally, which transitions the PLL into self clocked mode.
Self clocked mode frequency is the frequency at which the PLL operates when the reference frequency falls below f
default MFD/RFD settings.
This parameter is characterized before qualification rather than 100% tested.
Proper PC board layout procedures must be followed to achieve specifications.
This specification applies to the period required for the PLL to relock after changing the MFD frequency control bits in the
synthesizer control register (SYNCR).
Jitter is the average deviation from the programmed frequency measured over the specified interval at maximum f
Measurements are made with the device powered by filtered supplies and clocked by a stable external clock signal. Noise
injected into the PLL circuitry via V
for a given interval.
Based on slow system clock of 40 MHz measured at f
NUM
G1
G2
G3
G4
50 pF / 50 Ω for high drive
25 pF / 25 Ω for low drive
General Purpose I/O Timing
4, 5, 8 ,9
CLKOUT High to GPIO Output Invalid
CLKOUT High to GPIO Output Valid
CLKOUT High to GPIO Input Invalid
GPIO Input Valid to CLKOUT High
Characteristic
, measured at f
Table
Table 27. PLL Electrical Specifications (continued)
Characteristic
DDPLL
(V
.
DD
MCF52223 ColdFire Microcontroller, Rev. 2
and V
and V
SYS
Max
SSPLL
DDPLL
Table 28. GPIO Timing
and variation in crystal oscillator frequency increase the C
= 2.7 to 3.6 V, V
sys
max.
Table 28
SS
Symbol
and
C
f
f
= V
f
LCK
oco
UL
jitter
Symbol
t
Figure
t
CHPOV
t
CHPOI
t
SSPLL
PVCH
CHPI
= 0 V)
6.
–0.75
–1.5
7.84
Min
Min
1.5
1.5
and USB
9
Freescale Semiconductor
Max
0.75
8.16
interfaces. When in
1.5
.01
10
Max
10
jitter
percentage
sys
% f
LOR
% f
% f
MHz
Unit
.
Unit
sys
ns
ns
ns
ns
ref
ref
with

Related parts for mcf52221