ltc4267cgn-1 Linear Technology Corporation, ltc4267cgn-1 Datasheet - Page 16
![no-image](/images/manufacturer_photos/0/3/389/linear_technology_corporation_sml.jpg)
ltc4267cgn-1
Manufacturer Part Number
ltc4267cgn-1
Description
Power Over Ethernet Ieee 802.3af Pd Interface With Integrated Switching Regulator
Manufacturer
Linear Technology Corporation
Datasheet
1.LTC4267CGN-1.pdf
(32 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LTC4267CGN-1
Manufacturer:
LT
Quantity:
10 000
Part Number:
ltc4267cgn-1#PBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
APPLICATIO S I FOR ATIO
LTC4267-1
16
The undervoltage lockout mechanism on P
the LTC4267-1 switching regulator from trying to drive
the external N-Channel MOSFET with insuffi cient gate-to-
source voltage. The voltage at the P
V
momentarily to enable operation. The P
fall to V
before the undervoltage lockout disables the switching
regulator. This wide UVLO hysteresis range supports
applications where a bias winding on the fl yback trans-
former is used to increase the effi ciency of the LTC4267-1
switching regulator.
The I
with respect to PGND) to force the LTC4267-1 switching
regulator into shutdown. An internal 0.3μA current source
always tries to pull the I
the I
P
begins to operate and an internal clamp immediately pulls
the I
pin voltage will vary from roughly 0.7V to 1.9V to represent
current comparator thresholds from zero to maximum.
Internal Soft-Start
An internal soft-start feature is enabled whenever the
LTC4267-1 switching regulator comes out of shutdown.
Specifi cally, the I
prevented from reaching maximum until 1.4ms have
passed. This allows the input current of the PD to rise in a
smooth and controlled manner on start-up and stay within
the current limit requirement of the LTC4267-1 interface.
TURNON
VCC
TH
TH
TH
exceeds V
/RUN pin voltage is allowed to exceed V
/RUN can be driven below V
/RUN pin to about 0.7V. In operation, the I
TURNOFF
(nominally 8.7V with respect to PGND) at least
Figure 8. LTC4267-1 Switching Regulator
Start-Up/Shutdown State Diagram
TURNON
(nominally 5.7V with respect to PGND)
TH
U
/RUN voltage is clamped and is
, the LTC4267-1 switching regulator
TH
U
/RUN pin towards P
ITHSHDN
W
VCC
VCC
pin must exceed
(nominally 0.28V
voltage must
VCC
ITHSHDN
U
VCC
prevents
TH
. When
/RUN
and
Adjustable Slope Compensation
The LTC4267-1 switching regulator injects a 5μA peak
current ramp out through its SENSE pin which can be
used for slope compensation in designs that require it.
This current ramp is approximately linear and begins at
zero current at 6% duty cycle, reaching peak current at
80% duty cycle. Programming the slope compensation
via a series resistor is discussed in the External Interface
and Component Selection section.
EXTERNAL INTERFACE AND COMPONENT SELECTION
Input Interface Transformer
Nodes on an Ethernet network commonly interface to the
outside world via an isolation transformer (Figure 9). For
PoE devices, the isolation transformer must include a
center tap on the media (cable) side. Proper termination
is required around the transformer to provide correct
impedance matching and to avoid radiated and conducted
emissions. Transformer vendors such as Bel Fuse, Coil-
craft, Pulse and Tyco (Table 3) can provide assistance with
selection of an appropriate isolation transformer and proper
termination methods. These vendors have transformers
specifi cally designed for use in PD applications.
Table 3. Power over Ethernet Transformer Vendors
VENDOR
Bel Fuse Inc.
Coilcraft, Inc.
Pulse Engineering
Tyco Electronics
CONTACT INFORMATION
206 Van Vorst Street
Jersey City, NJ 07302
Tel: 201-432-0463
FAX: 201-432-9542
http://www.belfuse.com
1102 Silver Lake Road
Cary, IL 60013
Tel: 847-639-6400
FAX: 847-639-1469
http://www.coilcraft.com
12220 World Trade Drive
San Diego, CA 92128
Tel: 858-674-8100
FAX: 858-674-8262
http://www.pulseeng.com
308 Constitution Drive
Menlo Park, CA 94025-1164
Tel: 800-227-7040
FAX: 650-361-2508
http://www.circuitprotection.com
42671f