ltc6244hv Linear Technology Corporation, ltc6244hv Datasheet - Page 16
![no-image](/images/manufacturer_photos/0/3/389/linear_technology_corporation_sml.jpg)
ltc6244hv
Manufacturer Part Number
ltc6244hv
Description
Dual 50mhz, Low Noise, Rail-to-rail, Cmos Op Amp
Manufacturer
Linear Technology Corporation
Datasheet
1.LTC6244HV.pdf
(24 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ltc6244hvCDD
Manufacturer:
LT
Quantity:
10 000
Part Number:
ltc6244hvCDD#PBF
Manufacturer:
LT凌特厂
Quantity:
20 000
Company:
Part Number:
ltc6244hvCMS8
Manufacturer:
LT
Quantity:
10 000
Part Number:
ltc6244hvCMS8#TRPBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Company:
Part Number:
ltc6244hvHDD
Manufacturer:
LT
Quantity:
10 000
Company:
Part Number:
ltc6244hvHMS8
Manufacturer:
LT
Quantity:
10 000
Company:
Part Number:
ltc6244hvIDD
Manufacturer:
LT
Quantity:
10 000
Part Number:
ltc6244hvIMS8#PBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
APPLICATIO S I FOR ATIO
LTC6244
Large Area Photodiode Amplifi ers
A simple large area photodiode amplifi er is shown in
Figure 4a. The capacitance of the photodiode is 3650pF
(nominally 3000pF), and this has a signifi cant effect on
the noise performance of the circuit. For example, the
photodiode capacitance at 10kHz equates to an impedance
of 4.36kΩ, so the op amp circuit with 1MΩ feedback has a
noise gain of NG = 1 + 1M/4.36k = 230 at that frequency.
Therefore, the LTC6244 input voltage noise gets to the
output as NG • 7.8nV/√Hz = 1800nV/√Hz, and this can
clearly be seen in the circuit’s output noise spectrum in
Figure 4b. Note that we have not yet accounted for the
op amp current noise, or for the 130nV/√Hz of the gain
resistor, but these are obviously trivial compared to the op
Figure 4b. Output Noise Spectral Density of the Circuit of Figure
4a. At 10kHz, the 1800nV/√Hz Output Noise is Due Almost
Entirely to the 7.8nV Voltage Noise of the LTC6244 and the High
Noise Gain of the 1M Feedback Resistor Looking Into the High
Photodiode Capacitance
16
Figure 4a. Large Area Photodiode Transimpedance Amplifi er
S1227-1010BQ
HAMAMATSU
PHOTODIODE
C
LARGE AREA
PD
= 3000pF
1k
I
PD
U
–
LTC6244HV
+
1/2
FREQUENCY (Hz)
–5V
5V
U
3.9pF
6244 F04a
1M
10k
C
R
F
F
V
BW = 52kHz
NOISE = 1800nV/√Hz AT 10kHz
OUT
W
V
OUT
= 1M • I
PD
6244 F04b
100k
U
amp voltage noise and the noise gain. For reference, the
DC output offset of this circuit is about 100µV, bandwidth
is 52kHz, and the total noise was measured at 1.7mV
on a 100kHz measurement bandwidth.
An improvement to this circuit is shown in Figure 5a,
where the large diode capacitance is bootstrapped by a
1nV/√Hz JFET. This depletion JFET has a V
–0.5V, so that R
drain current. Connected as shown, the photodiode has a
reverse bias of one V
lower than in the previous case (measured 2640pF), but
the most drastic effects are due to the bootstrapping.
Figure 5b shows the output noise of the new circuit.
Noise at 10kHz is now 220nV/√Hz, and the 130nV/√Hz
noise thermal noise fl oor of the 1M feedback resistor
is discernible at low frequencies. What has happened is
that the 7.8nV/√Hz of the op amp has been effectively
replaced by the 1nV/√Hz of the JFET. This is because the
1M feedback resistor is no longer “looking back” into the
large photodiode capacitance. It is instead looking back
into a JFET gate capacitance, an op amp input capacitance,
and some parasitics, approximately 10pF total. The large
photodiode capacitance is across the gate-source volt-
age of the low noise JFET. Doing a sample calculation at
10kHz as before, the photodiode capacitance looks like
6kΩ, so the 1nV/√Hz of the JFET creates a current noise
of 1nV/6k = 167fA/√Hz. This current noise necessarily
fl ows through the 1M feedback resistor, and so appears
as 167nV/√Hz at the output. Adding the 130nV/√Hz of the
resistor (RMS wise) gives a total calculated noise density
of 210nV/√Hz, agreeing well with the measured noise of
Figure 5b. Another drastic improvement is in bandwidth,
now over 350kHz, as the bootstrap enabled a reduction
of the compensating feedback capacitance. Note that the
bootstrap does not affect the DC accuracy of the amplifi er,
except by adding a few picoamps of gate current.
There is one drawback to this circuit. Most photodiode
circuits require the ability to set the amount of applied
reverse bias, whether it’s 0V, 5V, or 200V. This circuit has
a fi xed reverse bias of about 0.5V, dictated by the JFET.
BIAS
forces it to operate at just over 1mA of
GS
, so its capacitance will be slightly
GS
of about
RMS
6244f