mc10xs3535 Freescale Semiconductor, Inc, mc10xs3535 Datasheet - Page 33
![no-image](/images/manufacturer_photos/0/2/263/freescale_semiconductor__inc_sml.jpg)
mc10xs3535
Manufacturer Part Number
mc10xs3535
Description
Smart Front Corner Light Switch Triple 10 M And Dual 35 M
Manufacturer
Freescale Semiconductor, Inc
Datasheet
1.MC10XS3535.pdf
(43 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
mc10xs3535DHFKR2
Manufacturer:
STM
Quantity:
3 000
Part Number:
mc10xs3535HFK
Manufacturer:
FREESCALE
Quantity:
20 000
Part Number:
mc10xs3535HFKR2
Manufacturer:
FREESCALE
Quantity:
20 000
Part Number:
mc10xs3535JH
Manufacturer:
FREESCALE
Quantity:
20 000
DIAGNOSTIC
Open Load
output (OUT1:OUT5 ) when the output pin is in the ON state.
Open load detection levels can be chosen by SPI to detect a
standard bulb, a Xenon bulb for OUT2 only, or LEDs (OLLED
bit). Open load for LEDs only is detected during each regular
switch-off state or periodically each t
D[6:0] = 7F)
must be on at least t
detected, the output stays ON.
Analog Integrated Circuit Device Data
Freescale Semiconductor
The 10XS3535 provides open load detection for each
OFF
out: OFF
autorestart = 0
external: IGN, FLASHER, FOG
external_ON: IGN_ON, Flasher_ON, FOG_ON
Note: * See Autorestart strategy chapter.
external_ON
external
(external_ON = 0)
.
(external_ON = 1)
To detect OLLED in fully on state, the output
(external_ON = 0)
(UV = 1)
(external_on = 1)
OLLED.
When an open load has been
Figure 14. Faults Management in Fail Mode (for OUT[1:5] only)
OCHI1
out: external
and
(UV = 1
OLLED
(external_ON = 0)
(fully-on,
(t>t
(OT = 1) or
(OCHI1 = 1)
OCHI1
(t>t
(UV* = 0)
1.4 sec min
autorestart
(t>t
) and (autorestart = 0)
OCHI1_AUTO
) and
OFF-latched
State
OFF Autorestart
out: OFF
autorestart=1
and the SPI read operation is needed (OL bit). In case of a
Power on Reset on VBAT, the fault will be reset.
Current Sense
done using the current sense (CSNS) pin connected to an
external resistor. The CSNS resistance value is defined in
function to VCC voltage value. It is recommended to use
resistor 500
5.0 V application. The routing of the current sense sources is
SPI programmable (MUX[2,0] bits).
) and (autorestart = 1)
(external_ON = 0)
To delatch the diagnosis, the condition should be removed
The 10XS3535 diagnosis for load current (OUT1:6) is
OCHI2
out: external
(OT=1)
Ω
(UV = 1) or (OCHI2 = 1)
< R
CSNS
PROTECTION AND DIAGNOSIS FEATURES
(t>t
OCHI2
< 5.0 k
FUNCTIONAL DEVICE OPERATION
(OCLO = 1) or
(UV = 1)
) and (autorestart = 0)
Ω
. Typical value is 1.0 k
(OT = 1
OCLO
out: external
10XS3535
Ω
for
33