tc7109a Microchip Technology Inc., tc7109a Datasheet - Page 6

• Manufacturer Part Number: tc7109a
• Description: 12-bit ?-compatible Analog-to-digital Converters
• Manufacturer: Microchip Technology Inc.

TC7109/A
2.0
The descriptions of the pins are listed in Table 2-1.
DS21456C-page 6
TABLE 2-1:
(40-Pin PDIP)
Pin Number
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
1
2
3
4
5
6
7
8
9
PIN DESCRIPTIONS
BUFF OSC OUT Buffered Oscillator Output.
PIN FUNCTION TABLE
RUN/HOLD
OSC OUT
CE/LOAD
OSC SEL
REF OUT
STATUS
Symbol
OSC IN
MODE
HBEN
SEND
LBEN
TEST
GND
POL
B
B
OR
B
B
B
B
B
B
B
B
B
B
V-
12
10
11
9
8
7
6
5
4
3
2
1
Digital ground, 0V, ground return for all digital logic.
Output HIGH during integrate and de-integrate until data is latched. Output LOW when
analog section is in auto-zero or zero integrator configuration.
Polarity – High for positive input.
Over Range – High if over ranged (Three-State Data bit).
Bit 12 (Most Significant bit) (Three-State Data bit).
Bit 11 (Three-State Data bit).
Bit 10 (Three-State Data bit).
Bit 9 (Three-State Data bit).
Bit 8 (Three-State Data bit).
Bit 7 (Three-State Data bit).
Bit 6 (Three-State Data bit).
Bit 5 (Three-State Data bit).
Bit 4 (Three-State Data bit).
Bit 3 (Three-State Data bit).
Bit 2 (Three-State Data bit).
Bit 1 (Least Significant bit) (Three-State Data bit).
Input High – Normal operation. Input LOW – Forces all bit outputs HIGH.
Note: This input is used for test purposes only.
Low Byte Enable – with MODE (Pin 21) LOW, and CE/LOAD (Pin 20) LOW, taking this pin
LOW activates low order byte outputs, B
low byte flag output used in Handshake mode. (See Figure 3-7, Figure , and Figure 3-9.)
High Byte Enable – with MODE (Pin 21) LOW, and CE/LOAD (Pin 20) LOW, taking this pin
LOW activates high order byte outputs, B
pin serves as high byte flag output used in Handshake mode. See Figures 3-7, 3-8, and 3-9.
Chip Enable/Load – with MODE (Pin 21) LOW, CE/LOAD serves as a master output enable.
When HIGH, B
strobe is used in handshake mode. (See Figure 3-7, Figure , and Figure 3-9.)
Input LOW – Direct Output mode where CE/LOAD (Pin 20), HBEN (Pin 19), and LBEN (Pin
18) act as inputs directly controlling byte outputs. Input Pulsed HIGH - Causes immediate
entry into Handshake mode and output of data as in Figure 3-9.
Input HIGH – enables CE/LOAD (Pin 20), HBEN (Pin 19), and LBEN (Pin 18) as outputs,
Handshake mode will be entered and data output as in Figure 3-7 and Figure 3-9
at conversions completion.
Oscillator Input.
Oscillator Output.
Oscillator Select – Input HIGH configures OSC IN, OSC OUT, BUFF OSC OUT as RC
oscillator – clock will be same phase and duty cycle as BUFF OSC OUT. Input LOW
configures OSC IN, OSC OUT for crystal oscillator - clock frequency will be 1/58 of frequency
at BUFF OSC OUT.
Input HIGH – Conversions continuously performed every 8192 clock pulses.
Input LOW – Conversion in progress completed; converter will stop in auto-zero seven
counts before integrate.
Input - Used in Handshake mode to indicate ability of an external device to accept data.
Connect to V+ if not used.
Analog Negative Supply – Nominally -5V with respect to GND (Pin 1).
Reference Voltage Output – Nominally 2.8V down from V+ (Pin 40).
1
–B
12
, POL, OR outputs are disabled. When MODE (Pin 21) is HIGH, a load
Description
1
9
–B
–B
8
12
. With MODE (Pin 21) HIGH, this pin serves as
, POL, OR. With MODE (Pin 21) HIGH, this
© 2006 Microchip Technology Inc.