sx8634 Semtech Corporation, sx8634 Datasheet - Page 49
![no-image](/images/manufacturer_photos/0/5/596/semtech_corporation_sml.jpg)
sx8634
Manufacturer Part Number
sx8634
Description
Low Power, Capacitive Button And Slider Touch Controller 12 Sensors With Enhanced Led Drivers And Proximity Sensing
Manufacturer
Semtech Corporation
Datasheet
1.SX8634.pdf
(80 pages)
- Current page: 49 of 80
- Download datasheet (1000Kb)
ADVANCED COMMUNICATIONS & SENSING
Small environmental and system noise cause the ticks to vary slowly around the zero idle mode value.
In case the ticks get slightly negative this is considered as normal operation. However large negative values will
trigger an offset compensation phase and a new set of DCVs will be obtained.
The decision to trigger a compensation phase based on negative ticks is determined by the value in the register
BtnCompNegThresh and by the number of ticks below the negative thresholds defined in register
BtnCompNegCntMax. An example is shown in Figure 50.
BtnCompNegThresh
BtnCompNegCntMax
BtnHysteresis
BtnStuckAtTimeout
Revision 7_6, October 10
In case the ticks get slightly positive this is considered as normal operation. Very large positive tick values
indicate a valid touch. The averaging filter is disabled as soon as the average reaches the value defined by
BtnAvgThresh. This mechanism avoids that a valid touch will be averaged and finally the tick difference
becomes zero.
In case three or more sensors reach the BtnAvgThresh value simultaneously then the SX8634 will start an
offset compensation procedure.
Small negative ticks are considered as normal operation and will occur very often.
Larger negative ticks however need to be avoided and a convenient method is to trigger an offset
compensation phase. The new set of DCV will assure the idle ticks will be close to zero again.
A trade-off has to be found for the value of this register. A negative threshold too close to zero will trigger a
compensation phase very often. A very negative threshold will never trigger.
As soon as the ticks get smaller than the Negative Threshold the Negative Counter starts to count.
If the counter goes beyond the Negative Counter Max then the offset compensation phase is triggered.
The recommended value for this register is ‘1’ which means that the offset compensation starts on the first tick
below the negative threshold.
The hysteresis percentage is identical for all buttons.
A touch is detected if the ticks are getting larger as the value defined by:
A release is detected if the ticks are getting smaller as the value defined by:
CapThreshold + CapThreshold * hysteresis.
CapThreshold - CapThreshold * hysteresis.
Figure 50
Negative Ticks Offset Compensation Trigger
(12 sensors) with Enhanced LED Drivers and Proximity Sensing
© 2010 Semtech Corp.
Low Power, Capacitive Button and Slider Touch Controller
49
DATASHEET
www.semtech.com
SX8634
Related parts for sx8634
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![6666](/images/manufacturer_photos/0/5/596/semtech_corporation_tmb.jpg)
Part Number:
Description:
HIGH VOLTAGE CAPACITORS MONOLITHIC CERAMIC TYPE
Manufacturer:
Semtech Corporation
Datasheet:
![EZ1084CM](/images/manufacturer_photos/0/5/596/semtech_corporation_tmb.jpg)
Part Number:
Description:
EZ1084CM5.0 AMP POSITIVE VOLTAGE REGULATOR
Manufacturer:
Semtech Corporation
Datasheet:
![EZ1587CM](/images/manufacturer_photos/0/5/596/semtech_corporation_tmb.jpg)
Part Number:
Description:
3.0 AMP LOW DROPOUT POSITIVE VOLTAGE REGULATORS
Manufacturer:
Semtech Corporation
Datasheet:
![ACS8515](/images/manufacturer_photos/0/5/596/semtech_corporation_tmb.jpg)
Part Number:
Description:
Manufacturer:
Semtech Corporation
Datasheet:
![SR3.3](/images/manufacturer_photos/0/5/596/semtech_corporation_tmb.jpg)
Part Number:
Description:
RailClamp Low Capacitance TVS Diode Array
Manufacturer:
Semtech Corporation
Datasheet:
![SC1151CS](/images/manufacturer_photos/0/5/596/semtech_corporation_tmb.jpg)
Part Number:
Description:
Manufacturer:
Semtech Corporation
Datasheet:
![SC1182CSW](/images/manufacturer_photos/0/5/596/semtech_corporation_tmb.jpg)
Part Number:
Description:
Manufacturer:
Semtech Corporation
Datasheet:
![SC1185CSW](/images/manufacturer_photos/0/5/596/semtech_corporation_tmb.jpg)
Part Number:
Description:
Manufacturer:
Semtech Corporation
Datasheet:
![SC1150CS](/images/manufacturer_photos/0/5/596/semtech_corporation_tmb.jpg)
Part Number:
Description:
Manufacturer:
Semtech Corporation
Datasheet:
![SC1152CS](/images/manufacturer_photos/0/5/596/semtech_corporation_tmb.jpg)
Part Number:
Description:
Manufacturer:
Semtech Corporation
Datasheet:
![MMBT9012](/images/manufacturer_photos/0/5/596/semtech_corporation_tmb.jpg)
Part Number:
Description:
Manufacturer:
Semtech Corporation
Datasheet:
![MMBT9013](/images/manufacturer_photos/0/5/596/semtech_corporation_tmb.jpg)
Part Number:
Description:
Manufacturer:
Semtech Corporation
Datasheet:
![MMBT9014](/images/manufacturer_photos/0/5/596/semtech_corporation_tmb.jpg)
Part Number:
Description:
Manufacturer:
Semtech Corporation
Datasheet: