wms7101100s ETC-unknow, wms7101100s Datasheet
wms7101100s
Related parts for wms7101100s
wms7101100s Summary of contents
Page 1
WMS7100 / 7101 NON-VOLATILE DIGITAL POTENTIOMETERS WITH UP/DOWN (3-WIRE) INTERFACE, 10KOHM, 50KOHM, 100KOHM RESISTANCE 256 TAPS WITHOUT / WITH OUTPUT BUFFER PRELIMINARY DATASHEET Publication Release Date: July 2003 - 1 - Revision 1.0 ...
Page 2
GENERAL DESCRIPTION The WMS7100/7101 is a single channel 256-tap non-volatile linear digital potentiometer available in 10KΩ, 50KΩ and 100KΩ resistance. The device consists of Up/Down serial interface, tap register, decoder, resistor array, wiper switches, NV memory and control logics. ...
Page 3
BLOCK DIAGRAM INC Up/Down CS Serial U /D Interface NV Memory V SS Control FIGURE 1 – WMS7100 BLOCK DIAGRAM (Rheostat/Divider Mode) INC Up/Down CS Serial U/D Interface NV Memory V SS Control FIGURE 2 – WMS7101 BLOCK DIAGRAM ...
Page 4
TABLE OF CONTENTS 1. GENERAL DESCRIPTION.................................................................................................................. 2 2. FEATURES ......................................................................................................................................... 2 3. BLOCK DIAGRAM............................................................................................................................... 3 4. TABLE OF CONTENTS ...................................................................................................................... 4 5. PIN CONFIGURATION ....................................................................................................................... 5 6. PIN DESCRIPTION ............................................................................................................................. 6 7. FUNCTIONAL DESCRIPTION............................................................................................................ 7 7.1. Rheostat And Divider ...
Page 5
PIN CONFIGURATION 1 INC U 8-M SOP 1 INC 2 U 8-PDIP INC CS 7 U/D 2 ...
Page 6
PIN DESCRIPTION Pin Name Chip Select: When CS is LOW, the device is enabled. CS When CS is HIGH, the part is deselected and is in standby mode Up/Down Control: HIGH state enables the wiper to move towards the ...
Page 7
FUNCTIONAL DESCRIPTION 7. HEOSTAT ND IVIDER The WMS7100 device can operate as either a two-terminal variable resistor or a three-terminal voltage divider without an output buffer. However, the WMS7101 can only operate in a three-terminal voltage ...
Page 8
ERIAL ATA NTERFACE The WMS7100/7101 device has a 3-wire Up/Down Serial Interface consisting INC and U/ D control signals. The key features of this interface include: • Enabling the device • Determining the ...
Page 9
TIMING DIAGRAMS Conditions +2.7V to 5.5V [1] t PUD INC FIGURE 3 –WMS7100/1 TIMING DIAGRAM Note: [1] This only applies to the ...
Page 10
TABLE 10 – TIMING PARAMETERS PARAMETERS CS to INC Setup INC Setup INC Hold INC LOW Period INC HIGH Period INC Inactive to CS Inactive CS Deselect Time (NO STORE) CS Deselect Time (STORE) ...
Page 11
ABSOLUTE MAXIMUM RATINGS & OPERATING CONDITIONS TABLE 11 – ABSOLUTE MAXIMUM RATINGS (PACKAGED PARTS) Conditions Junction temperature Storage temperature Voltage applied to any pad Lead temperature (soldering – 10 seconds) V – TABLE 12 – OPERATING ...
Page 12
ELECTRICAL CHARACTERISTICS TABLE 12 – ELECTRICAL CHARACTERISTICS (Packaged parts) PARAMETERS SYMBOL Rheostat Mode Nominal Resistance [2] Different Non Linearity [2] Integral Non Linearity [1] Tempo [2] Wiper Resistance Wiper Current Divider Mode Resolution [2] Different Non Linearity [2] Integral ...
Page 13
TABLE 12 – ELECTRICAL CHARACTERISTICS (Packaged parts) – Cont’d PARAMETERS SYMBOL Input Leakage Current Output Leakage Current [1] Input Capacitance [1] Output Capacitance Power Requirements Operating Voltage Operating Current Standby Current Power Supply Rejection Ratio Notes: [1] Not subject to ...
Page 14
T C EST IRCUITS 1LSB= V+/255 WMS71xx *Assume infinite input impedance Potentiometer divider nonlinearity error test circuit (INL, DNL) No Connection WMS71xx ...
Page 15
TYPICAL APPLICATION CIRCUITS Vin WMS71XX OUT (256- 256 R = Total resistance of potentiometer Wiper setting for WMS71XX FIGURE ...
Page 16
WMS71xx Vout FIGURE 7 – WMS7101 TRIMMING VOLTAGE REFERENCE CS\ U/D\ INC\ FIGURE 8 – WMS7101 RF AMP CONTROL V+ V REFH 5V 0V GND C1 0.1uF CS U/ INC ...
Page 17
L C AYOUT ONSIDERATIONS Use a 0.1µF bypass capacitor as close as possible to the V performance. Often this can be done by placing the surface mount capacitor on the bottom side of the PC board, directly between the ...
Page 18
PACKAGE DRAWINGS AND DIMENSIONS 8 1 Control demensions are in milmeters . E θ FIGURE 10: 8L 150MIL SOIC - 18 - WMS7100 / 7101 ...
Page 19
...
Page 20
FIGURE 12: 8L 3MM MSOP - 20 - WMS7100 / 7101 ...
Page 21
... End-to-end Resistance: 010: 10Kohm 050: 50Kohm 100: 100Kohm Package: S: SOIC P: PDIP M: MSOP SOIC PDIP WMS7100010S WMS7100010P WMS7100050S WMS7100050P WMS7100100S WMS7100100P WMS7101010S WMS7101010P WMS7101050S WMS7101050P WMS7101100S WMS7101100P - 21 - WMS7100 / 7101 MSOP WMS7100010M WMS7100050M WMS7100100M WMS7101010M WMS7101050M WMS7101100M Publication Release Date: July 2003 Revision 1.0 ...
Page 22
VERSION HISTORY VERSION DATE 1.0 July 2003 Initial issue The contents of this document are provided only as a guide for the applications of Winbond products. Winbond makes no representation or warranties with respect to the accuracy or completeness ...