atf750c-15xc ATMEL Corporation, atf750c-15xc Datasheet
atf750c-15xc
Related parts for atf750c-15xc
atf750c-15xc Summary of contents
Page 1
... I/O GND * I/O GND High-speed Complex Programmable Logic Device ATF750C ATF750CL 10 I/O PINS PLCC/LCC I/O I GND * I/O 0776K–PLD–07/07 ...
Page 2
... Atmel’s proven electrically-erasable technology. Each of the ATF750C(L)’s 22 logic pins can be used as an input. Ten of these can be used as inputs, outputs or bi-directional I/O pins. Each flip-flop is individually config- urable as either D- or T-type. Each flip-flop output is fed back into the array independently ...
Page 3
... Logic Options Combinatorial Output Combined Terms Clock Mux Output Options 0776K–PLD–07/07 Registered Output Combined Terms Separate Terms CKMUX CKi CLK CLOCK PIN SELECT PRODUCT TERM ATF750C(L) Separate Terms TO LOGIC CELL 3 ...
Page 4
... I/O Diagram ATF750C(L) 4 All input and I/O pins on the ATF750C(L) have programmable “pin-keeper” circuits. If activated, when any pin is driven high or low and then subsequently left floating, it will stay at that previous high or low level. This circuitry prevents unused input and I/O lines from floating to intermediate voltage levels, which causes unnecessary power consumption and system noise ...
Page 5
... Mil Min Com -4 Min < (10 VCC 300 (390 MIL.) 390 (750 MIL.) ATF750C(L) Min Typ Max 10 10 125 180 135 190 125 180 135 190 0.12 1 0.15 2 -120 -0.6 0.8 2 0.75 CC 0.5 0.5 0.8 2.4 Units µA µ ...
Page 6
... MAX SF No Feedback 1/( Asynchronous Reset Width AW t Asynchronous Reset Recovery Time AR t Asynchronous Reset to Registered Output Reset AP t Setup Time, Synchronous Preset SP Note: 1. See ordering information for valid part numbers. ATF750C(L) 6 (1) (1) Min 3 -10 ...
Page 7
... AW t Asynchronous Reset Recovery Time ARS t Asynchronous Reset to Registered Output Reset AP t Setup Time, Synchronous Preset SPS 0776K–PLD–07/07 (1) Min 3 COS + t ) CFS ATF750C(L) -7 -10 C/CL-15 Max Min Max Min 7.5 10 7.5 10 7 8/12 ...
Page 8
... Functional Logic Diagram ATF750C, Upper Half ATF750C(L) 8 0776K–PLD–07/07 ...
Page 9
... Functional Logic Diagram ATF750C, Lower Half 0776K–PLD–07/07 ATF750C(L) 9 ...
Page 10
... Power-up Reset ATF750C(L) 10 The registers in the ATF750C(L)s are designed to reset during power-up point delayed slightly from V crossing V CC output state will depend on the polarity of the output buffer. This feature is critical for state machine initialization. However, due to the asynchronous nature of reset and the uncertainty of how V conditions are required: 1 ...
Page 11
... Independent I/O Pin and Feedback Paths Each I/O pin on the ATF750C(L) has a dedicated input path. Each of the 20 registers has its own feedback terms into the array as well. This feature, combined with individual product terms for each I/O’s output enable, facilitates true bi- directional I/O design ...
Page 12
... Additionally, the ATF750C may be programmed to perform the ATV750(L) functional subset (no T-type flip-flops, pin clocking or D/T2 feedback) using the ATV750 JEDEC file. In this case, the ATF750C becomes a direct replacement or speed upgrade for the ATV750. The ATF750C is a direct replacement for the ATV750(L) and the ATV750B(L). ...
Page 13
... Preload of Registered Outputs 0776K–PLD–07/07 The ATF750C(L)’s registers are provided with circuitry to allow loading of each register asynchronously with either a high or a low. This feature will simplify testing since any state can be forced into the registers to control test sequencing pin will force the register high The PRELOAD state is entered by placing a 10 ...
Page 14
... OH 0.00 -10.00 -20.00 -30.00 -40.00 -50.00 -60.00 -70.00 -80.00 -90.00 5.5 6 ATF750CL SUPPLY CURRENT VS. SUPPLY VOLTAGE (T = 25°C) A 4.75 5.00 SUPPLY VOLTAGE (V) SUPPLY CURRENT VS. FREQUENCY LOW-POWER ("L") VERSION (T = 25° FREQUENCY (MHz) ATF750C/CL OUTPUT SOURCE CURRENT VS. OUTPUT VOLTAGE ( 0.00 0.50 1.00 1.50 2.00 2.50 3.00 3.50 V (V) OH 5.25 5.50 75 100 = 25°C) 4.00 4.50 5.00 0776K–PLD–07/07 ...
Page 15
... ATF750C(L) ATF750C/CL OUTPUT SINK CURRENT VS. OUTPUT VOLTAGE ( 140 120 100 0.5 1 1 (V) OL ATF750C/CL INPUT CURRENT VS. INPUT VOLTAGE (V = 5V,T = 25° -10 -15 -20 -25 0 0.5 1 1.5 2 2.5 3 3.5 4 INPUT VOLTAGE (V) ATF750C/CL INPUT CLAMP CURRENT VS ...
Page 16
... ATF750C-10JC ATF750C-10PC 24P3 ATF750C-10SC (1) ATF750C-10XC 24X ATF750C-10JI ATF750C-10PI 24P3 ATF750C-10SI ATF750C-10GM/883 24D3 ATF750C-10NM/883 5962-0720101MLA 24D3 5962-0720101M3A ATF750C-15JC ATF750C-15PC 24P3 ATF750C-15SC (1) ATF750C-15XC 24X ATF750C-15JI ATF750C-15PI 24P3 ATF750C-15SI ATF750C-15GM/883 24D3 ATF750C-15NM/883 5962-0720102MLA 24D3 5962-0720102M3A ATF750CL-15JC ATF750CL-15PC 24P3 ATF750CL-15SC (1) ATF750CL-15XC 24X ATF750CL-15JI ATF750CL-15PI 24P3 ...
Page 17
... ATF750C(L) Green Package Options (Pb/Halide-free/RoHS Compliant) Ext COS MAXS (ns) (ns) (MHz) 7.5 6 Using “C” Product for Industrial To use commercial product for industrial ranges, down-grade one speed grade from the “I” to the “C” device (7 ns “C” “ ...
Page 18
... MIL-STD 1835 D-9 Config A (Glass Sealed) 5.08(0.200) MAX SEATING PLANE 5.08(0.200) 3.18(0.125) 2.45(0.100)BSC 0.46(0.018) 0.20(0.008) 2325 Orchard Parkway San Jose, CA 95131 R ATF750C(L) 18 32.51(1.280) 31.50(1.240) 27.94(1.100) REF 1.65(0.065) 1.14(0.045) 8.13(0.320) 7.37(0.290) 0º~ 15º REF 10.20(0.400) MAX TITLE 24D3, 24-lead, 0.300" Wide. Non-windowed, Ceramic ...
Page 19
... Lead coplanarity is 0.004" (0.102 mm) maximum. 2325 Orchard Parkway San Jose, CA 95131 R 0776K–PLD–07/07 1.14(0.045) X 45˚ PIN NO. 1 IDENTIFIER TITLE 28J, 28-lead, Plastic J-leaded Chip Carrier (PLCC) ATF750C(L) 0.318(0.0125) 0.191(0.0075) D2/ COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX A 4 ...
Page 20
... LCC Dimensions in Millimeters and (Inches). Controlling dimension: Inches. MIL-STD 1835 C-4 11.68(0.460) 11.23(0.442) 7.62(0.300) BSC 1.27(0.050) TYP 2325 Orchard Parkway San Jose, CA 95131 R ATF750C(L) 20 11.68(0.460) 11.23(0.442) PIN 1 1.40(0.055) 1.14(0.045) 2.41(0.095) 1.91(0.075) 7.62(0.300) BSC TITLE 28L, 28-pad, Non-windowed, Ceramic Lid, Leadless Chip Carrier (LCC) 2 ...
Page 21
... Mold Flash or Protrusion shall not exceed 0.25 mm (0.010"). 2325 Orchard Parkway San Jose, CA 95131 R 0776K–PLD–07/07 D PIN TITLE 24P3, 24-lead (0.300"/7.62 mm Wide) Plastic Dual Inline Package (PDIP) ATF750C( COMMON DIMENSIONS (Unit of Measure = mm) MIN NOM SYMBOL A – – A1 0.381 – D 31.623 – ...
Page 22
... SOIC PIN 1 ID PIN 1 E 0º ~ 8º 2325 Orchard Parkway San Jose, CA 95131 R ATF750C( TITLE 24S, 24-lead (0.300" body) Plastic Gull Wing Small Outline (SOIC) COMMON DIMENSIONS (Unit of Measure = mm) MIN MAX SYMBOL NOM NOTE A – ...
Page 23
... Orchard Parkway San Jose, CA 95131 R 0776K–PLD–07/07 0.30(0.012) 0.19(0.007) 4.48(0.176) 4.30(0.169) 0.65(0.0256)BSC 7.90(0.311) 7.70(0.303) 0.15(0.006) 0.05(0.002) 0.75(0.030) 0.45(0.018) TITLE 24X, 24-lead (4.4 mm body width) Plastic Thin Shrink Small Outline Package (TSSOP) ATF750C(L) 6.50(0.256) 6.25(0.246) 1.20(0.047)MAX 0.20(0.008) 0.09(0.004) 04/11/2001 DRAWING NO. 24X REV ...
Page 24
... Revision History Revision Level – Release Date History K – July 2007 Added military-grade devices. Added fully-green RoHS-compliant devices in select speed grades and packages. ATF750C(L) 24 0776K–PLD–07/07 ...
Page 25
... Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. © 2007 Atmel Corporation. All rights reserved. Atmel marks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. International Atmel Asia ...