mic2292-34yml Micrel Semiconductor, mic2292-34yml Datasheet
![no-image](/images/manufacturer_photos/0/4/435/micrel_semiconductor_sml.jpg)
mic2292-34yml
Available stocks
Related parts for mic2292-34yml
mic2292-34yml Summary of contents
Page 1
... MIC2292/93 General Description The MIC2292 and MIC2293 are high frequency, Pulse Width Modulator (PWM) boost regulators optimized for constant- current, white LED driver applications. Because of their constant PWM switching frequencies of 1.6MHz and 2MHz, respectively, the MIC2292/93 can use the smallest external components, allowing designers to avoid sensitive IF bands in their RF applications ...
Page 2
... MIC2292/93 Ordering Information Marking Part Number Code MIC2292-15BML SWA MIC2292-15YML SWA MIC2292-34BML SWC MIC2292-34YML SWC MIC2293-15BML SZA MIC2293-15YML SZA MIC2293-34BML SZC MIC2293-34YML SZC Pin Configuration Pin Description Pin Number Pin Name 1 OUT 2 VIN 4,8 GND EP GND M9999-070105 ...
Page 3
... V = 10V EN SW TURN ON TURN OFF V = 10V EN MIC2292 MIC2293 I = 150mA 30V R MIC2292/93-15 MIC2292/93-34 Hysteresis , and the ambient temperature The maximum allowable power dissipation will result in excessive Micrel, Inc. (2) ) ..........................................2.5V to 10V IN ) ....................................... OUT IN ) ............ –40°C to +125° .............................................. 93°C/W JA ≤ ...
Page 4
... MIC2292/93 Typical Characteristics Feedback Voltage vs. Input Voltage 100 (V) IN Switch Frequency vs. Temperature 1.4 1.2 1 0.8 0.6 0.4 0.2 0 -40 - 100 TEMPERATURE (°C) Schottky Reverse Leakage Current 2 25V 1 16V R 0 10V 100 TEMPERATURE (° ...
Page 5
... Schottky rectifier diode. The oscillator generates a 1.6MHz clock for the MIC2292 and a 2.0MHz clock for the MIC2293. The clocks' two functions are to trigger the PWM generator that turns on the output transistor and to reset the slope compensation ramp generator. The current amplifi ...
Page 6
... MIC2292/93 External Component Selection The MIC2292/93 can be used across a wide rage of applica- Series LEDs 2 22µH 15µH 10µH 6.8µH 4.7µH 3 22µH 15µH 10µH 6.8µH 4.7µH 4 22µH 15µH 10µH 6.8µH 4.7µ 22µH 15µH 10µH 6.8µH 4.7µ 22µH 15µH 10µ ...
Page 7
... If the LEDs are disconnected from the circuit case an LED fails open, the sense resistor will pull the FB pin to ground. This will cause the MIC2292/93 to switch with a high duty-cycle resulting in output overvoltage. This may cause the SW pin voltage to exceed its maximum voltage rating, possibly damaging the IC and the external components ...
Page 8
... MIC2292/93 Functional Characteristics 6-Series LED Circuit with External Soft-Start TIME (100µs/ M9999-070105 6-Series LED Circuit without External Soft-Start L = 10µ 1µ 0.22µF OUT 20mA OUT 6 LEDs C = 2200pF 10kΩ 8 Micrel, Inc 10µ 1µ 0.22µF ...
Page 9
... MIC2292/93 Package Information MICREL INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA + 1 (408) 944-0800 TEL This information furnished by Micrel in this data sheet is believed to be accurate and reliable. However no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. ...