mc33880 Freescale Semiconductor, Inc, mc33880 Datasheet - Page 13
![no-image](/images/manufacturer_photos/0/2/263/freescale_semiconductor__inc_sml.jpg)
mc33880
Manufacturer Part Number
mc33880
Description
Configurable Octal Serial Switch With Serial Peripheral Interface I/o
Manufacturer
Freescale Semiconductor, Inc
Datasheet
1.MC33880.pdf
(25 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
mc33880DW
Manufacturer:
MOT
Quantity:
5 510
Company:
Part Number:
mc33880DW
Manufacturer:
COPAL
Quantity:
5 510
Part Number:
mc33880DW
Manufacturer:
MOTOROLA/摩托罗拉
Quantity:
20 000
Company:
Part Number:
mc33880DWB
Manufacturer:
FREESCALE Semiconductor
Quantity:
1
Part Number:
mc33880PEG
Manufacturer:
FREESCALE
Quantity:
20 000
Part Number:
mc33880PEGR2
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Part Number:
mc33880PEW
Manufacturer:
FREESCALE
Quantity:
20 000
switch with 8-bit serial control. The 33880 incorporates
SMARTMOS™ 5 technology with CMOS logic, bipolar/MOS
analog circuitry, and independent double diffused DMOS
power output transistors. Many benefits are realized as a
direct result of using this mixed technology. A simplified
internal block diagram of the 33880 is shown in
page 2.
CHIP SELECT (CS)
through the use of the
low state, data can be transferred from the MCU to the 33880
device and vice versa. Clocked-in data from the MCU is
transferred from the 33880 shift register and latched into the
power outputs on the rising edge of the
falling edge of the
transferred from the power outputs status register into the
device's shift register. The falling edge of
output driver. Whenever the
the DO pin output is enabled, thereby allowing information to
be transferred from the 33880 to the MCU. To avoid any
spurious data, it is essential the high-to-low transition of the
CS
SYSTEM CLOCK (SCLK)
registers of the 33880. The serial data input (DI) is latched
into the input shift register on the falling edge of the SCLK.
The serial data output pin (DO) shifts data out of the shift
register on the rising edge of the SCLK signal. False clocking
of the shift register must be avoided to guarantee validity of
data. It is essential the SCLK pin be in a logic low state
whenever chip select pin (
reason, it is recommended the SCLK pin is commanded to a
logic low state when the device is not accessed (
high state). When the
the SCLK and DI pin is ignored and the DO is tri-stated (high
impedance).
DATA INPUT (DI)
information is latched into the input register on the falling
edge of SCLK. A logic high state present on DI will program
a specific output on. The specific output will turn on with the
rising edge of the
present on the DI pin will program the output off. The specific
output will turn off with the rising edge of the
program the eight outputs of the 33880 device on or off, enter
Analog Integrated Circuit Device Data
Freescale Semiconductor
The 33880 is an eight-output hardware configurable power
The system MCU selects the 33880 to communicate
The system clock pin (SCLK) clocks the internal shift
This pin is used for serial instruction data input. DI
signal occurs only when SCLK is in a logic low state.
CS
CS
signal. Conversely, a logic low state
CS
signal, output status information is
CS
is in a logic high state, any signal at
pin. Whenever the pin is in a logic
CS
CS
) makes any transition. For this
pin goes to a logic low state,
CS
CS
FUNCTIONAL DESCRIPTION
signal. On the
FUNCTIONAL PIN DESCRIPTION
enables the DO
CS
Figure
signal. To
CS
in logic
INTRODUCTION
2,
DMOS output transistors exhibiting low drain-to-source ON
resistance values (R
CMOS control logic. All outputs have independent voltage
clamps to provide fast inductive turn-off and transient
protection. Operational bias currents of less than 4.0 mA on
V
are a direct result of using SMARTMOS™ 5 technology.
the DI pin beginning with Output 8, followed by Output 7,
Output 6, and so on to Output 1. For each falling edge of the
SCLK while
loaded into the shift register per the data bit DI state. Eight
bits of entered information fills the shift register. To preserve
data integrity, do not transition DI as SCLK transitions from a
high to low logic state.
DATA OUTPUT (DO)
register. The DO pin remains tri-state until the
a logic low state. All faults on the 33880 device are reported
as logic [1] through the DO data pin. Regardless of the
configuration of the driver, open loads and shorted loads are
reported as logic [1]. Conversely, normal operating outputs
with non-faulted loads are reported as logic [0]. The first
positive transition of SCLK will make output eight status
available on DO pin. Each successive positive clock will
make the next output status available. The DI/DO shifting of
data follows a first-in-first-out protocol with both input and
output words transferring the most significant bit (MSB) first.
ENABLE (EN)
the internal charge pump. The EN pin must be high for this
device to enhance the gates of the output drivers, perform
fault detection, and reporting. Active outputs during a low
transition of the EN pin will become active again when the EN
transitions high. If this feature is not required, it is
recommended the EN pin be connected to V
COMMAND INPUT (IN5 AND IN6)
five and six to be used in PWM applications. IN5 and IN6 pins
are ORed with the SPI communication input. For SPI control
of outputs five and six, the IN5 and IN6 pins should be
grounded or held low by the microprocessor. In the same
manner, when using the PWM feature the SPI port must
command the outputs off. Maximum PWM frequency for each
output is 2.0 kHz.
DD
The 33880 device uses high-efficiency updrain power
The serial data output (DO) pin is the output from the shift
The EN pin on the 33880 device either enables or disables
The IN5 and IN6 pins command inputs allowing outputs
and 12 mA on V
CS
is logic low, a data bit instruction (on or off) is
PWR
DS(ON)
with any combination of outputs ON
≤ 0.55 Ω at 25°C) and dense
FUNCTIONAL DESCRIPTION
INTRODUCTION
DD
CS
.
pin goes to
33880
13