mic37100 Micrel Semiconductor, mic37100 Datasheet
mic37100
Available stocks
Related parts for mic37100
mic37100 Summary of contents
Page 1
... MIC37100/01/02 offers extremely low dropout (typically 280mV at 1A) and low ground current (typically 11mA at 1A). The MIC37100 is a fixed output regulator offered in the SOT-223 package. The MIC37101 and MIC37102 are fixed and adjustable regulators, respectively thermally enhanced power 8-pin SOIC (small outline package) and the SOT-223 package ...
Page 2
... MIC37101-2.5BM MIC37101-2.5YM MIC37101-3.3BM MIC37101-3.3YM MIC37102BM MIC37102YM MIC37102BR MIC37102WR* * RoHS compliant with ‘high-melting solder’ exemption. Pin Configuration GND TAB GND SOT-223 (S) MIC37100-x.x (Fixed OUT 3 FLG 4 8-Pin SOIC MIC37101-x.x (Fixed) September 2007 Voltage Pb-Free / 1.5V 1.65V 1.8V 2 ...
Page 3
... FLG 4 5 ADJ 5–8 3, TAB GND 3 MIC37100/37101/37102 Pin Description Enable (Input): CMOS-compatible control input. Logic high = enable, logic low or open = shutdown. Supply (Input). Regulator Output. Flag (Output): Open-collector error flag output. Active low = output under voltage. Adjustment Input: Feedback input. Connect to resistive voltage-divider network ...
Page 4
... V = 2.25V 0. 2.250V 250µ OUT % of V OUT 4 MIC37100/37101/37102 (2) )...................................... +2.25V to +6V IN )............................................ 0V to +6V EN D(max) ) ........................ –40°C to +125°C J SOT-223 (θ ) ....................................................15°C/W JC SOIC-8 (θ ).......................................................20°C/W JC S-PAK-5 (θ ).......................................................2°C/W JC < +125°C, unless noted. J Min – ...
Page 5
... I GND IN GND 8. V ≤ 0.8V, V ≤ 6V, and OUT September 2007 (worst case) ÷ (T – where T OUT J(max) J(min OUT 5 MIC37100/37101/37102 is +125°C and T is –40°C. J(max) J(min 1V. For output voltages below 2.25V, dropout voltage is IN OUT M9999-090607 ...
Page 6
... Micrel, Inc. Typical Characteristics September 2007 6 MIC37100/37101/37102 M9999-090607 ...
Page 7
... Micrel, Inc. Typical Characteristics (continued) September 2007 7 MIC37100/37101/37102 M9999-090607 ...
Page 8
... Micrel, Inc. Typical Characteristics (continued) September 2007 8 MIC37100/37101/37102 M9999-090607 ...
Page 9
... Micrel, Inc. Functional Characteristics September 2007 9 MIC37100/37101/37102 M9999-090607 ...
Page 10
... EN MIC37101 MIC37101 Fixed Regulator with Flag and Enable Block Diagram IN EN MIC37102 September 2007 1.240V Ref. Thermal Shut- down MIC37100 MIC37100 Fixed Regulator Block Diagram 1.180V 1.240V Ref. 1.240V Ref. MIC37102 Adjustable Regulator Block Diagram 10 MIC37100/37101/37102 OUT Thermal Shut- down OUT ...
Page 11
... V voltage Transient Response and 3.3V to 2.5V or 2.5V to 1.8V, 1.65V or 1.5V Conversion The MIC37100/01/02 has excellent transient response to variations in input voltage and load current. The device has been designed to respond quickly to load current variations and input voltage variations. Large output capacitors are not required to obtain this performance. A ...
Page 12
... Micrel, Inc. without operating in dropout, NPN-based regulators require an input voltage of 3.7V at the very least. The MIC37100 regulator will provide excellent performance with an input as low as 3.0V or 2.5V respectively. This gives the PNP based regulators a distinct advantage over older, NPN based linear regulators. Minimum Load Current The MIC37100/01/02 regulator is specifi ...
Page 13
... Figure 5 shows that the required area of copper is 160mm The θ depending upon the availability of copper ground plane to which it is attached. × GND MIC37100/37101/37102 this package is ideally 63°C/W, but it will vary JA 900 T = 125°C 800 J 700 T = 85° ...
Page 14
... Micrel, Inc. Package Information September 2007 SOT-223 (S) 5-Pin S-PAK (R) 14 MIC37100/37101/37102 M9999-090607 ...
Page 15
... Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully September 2007 8-Pin SOIC (M) indemnify Micrel for any damages resulting from such use or sale. © 2005 Micrel, Incorporated. 15 MIC37100/37101/37102 M9999-090607 ...