lmh6551qmmx National Semiconductor Corporation, lmh6551qmmx Datasheet
lmh6551qmmx
Related parts for lmh6551qmmx
lmh6551qmmx Summary of contents
Page 1
... LMH6551Q suitable for use amplifier in high performance communications equipment. The LMH6551Q is available in the MSOP package. Typical Application LMH ® registered trademark of National Semiconductor Corporation. © 2012 Texas Instruments Incorporated LMH6551Q Features ■ 370 MHz −3 dB bandwidth (V ■ ...
Page 2
... LMH6551QMM 8–Pin MSOP LMH6551QMME LMH6551QMMX **Automotive Grade (Q) product incorporates enhanced manufacturing and support processes for the automotive market, including defect detection methodologies. Reliability qualification is compliant with the requirements and temperature grades defined in the AEC-Q100 standard. Automotive grade products are identified with the letter Q. For more information go to http://www.national.com/ automotive ...
Page 3
Absolute Maximum Ratings If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and specifications. ESD Tolerance (Note 5) Human Body Model Machine Model Supply Voltage Common Mode Input Voltage Maximum Input Current (pins ...
Page 4
Symbol Parameter V Pin Input Characteristics (Common Mode Feedback Amplifier Input Offset Voltage OSC Input Offset Voltage Average Temperature Drift Input Bias Current V CMRR CM Input Resistance Common Mode Gain Output Performance Output Voltage Swing Output Common ...
Page 5
Symbol Parameter Input Characteristics (Differential) V Input Offset Voltage OSD Input Offset Voltage Average Temperature Drift I Input Bias Current BIAS Input Bias Current Average Temperature Drift Input Bias Current Difference CMRR Common-Mode Rejection Ratio Input Resistance Input Capacitance V ...
Page 6
Symbol Parameter Slew Rate Rise/Fall Time, 10% to 90% V Pin AC Performance (Common Mode Feedback Amplifier) CM Common Mode Small Signal Bandwidth Distortion and Noise Response HD2 2 nd Harmonic Distortion HD2 HD3 3 rd Harmonic Distortion HD3 Input ...
Page 7
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but specific performance is not guaranteed. For guaranteed specifications, see the Electrical ...
Page 8
Suggested R vs. Cap Load OUT 1 V Pulse Response Single Ended Input PP Large Signal Pulse Response www.ti.com Suggested R 30157922 2 V Pulse Response Single Ended Input PP 30157926 Output Common Mode Pulse Response 30157935 8 vs. Cap ...
Page 9
Distortion vs. Frequency Distortion vs. Frequency Distortion vs. Supply Voltage (Single Supply) Distortion vs. Frequency 30157928 Distortion vs. Supply Voltage (Split Supplies) 30157936 Maximum V 30157937 9 30157929 30157938 vs. I OUT OUT 30157930 www.ti.com ...
Page 10
Minimum V OUT Closed Loop Output Impedance PSRR www.ti.com vs. I OUT 30157931 30157918 30157919 10 Closed Loop Output Impedance 30157917 Closed Loop Output Impedance 30157939 PSRR 30157920 ...
Page 11
CMRR Application Section The LMH6551Q is a fully differential amplifier designed to provide low distortion amplification to wide bandwidth differ- ential signals. The LMH6551Q, though fully integrated for ultimate balance and distortion performance, functionally pro- vides three channels. Two of ...
Page 12
With differential output voltage swing and linear drive current the LMH6551Q makes an excellent ca- ble driver as shown in Figure 2. The LMH6551Q is also suitable for driving differential cables from ...
Page 13
SINGLE SUPPLY OPERATION The input stage of the LMH6551Q has a built in offset of 0.7V towards the lower supply to accommodate single supply op- eration with single ended inputs. As shown in input common mode voltage is less than ...
Page 14
DRIVING ANALOG TO DIGITAL CONVERTERS Analog to digital converters (ADC) present challenging load conditions. They typically have high impedance inputs with large and often variable capacitive components. As well, there are usually current spikes associated with switched ca- pacitor or ...
Page 15
FIGURE 9. Calculating Transformer Circuit Net Gain FIGURE 10. Transformer Out Low Impedance Load 30157932 30157906 FIGURE 11. Driving 50Ω Test Equipment 15 30157903 www.ti.com ...
Page 16
CAPACITIVE DRIVE As noted in the DRIVING ANALOG TO DIGITAL CONVERT- ERS section, capacitive loads should be isolated from the amplifier output with small valued resistors. This is particularly the case when the load has a resistive component that is ...
Page 17
EVALUATION BOARD National Semiconductor offers evaluation board(s) to aid in device testing and characterization and as a guide for proper layout. Generally, a good high frequency layout will keep power supply and ground traces away from the inverting input and ...
Page 18
Physical Dimensions www.ti.com inches (millimeters) unless otherwise noted 8–Pin MSOP NS Package Number MUA08A 18 ...
Page 19
Notes 19 www.ti.com ...
Page 20
Notes ...