v23818-k305-l56 Infineon Technologies Corporation, v23818-k305-l56 Datasheet - Page 6

• Manufacturer Part Number: v23818-k305-l56
• Description: Small Form Factor Multimode 1.0625 Fibre Channel Gigabit Ethernet Transceiver With Connector
• Manufacturer: Infineon Technologies Corporation

Small Form Factor multisourcing footprint and dimensions
Published by Infineon Technologies AG
©
All Rights Reserved
Attention please!
The information herein is given to describe certain components and shall not be
considered as warranted characteristics.
Terms of delivery and rights to technical change reserved.
We hereby disclaim any and all warranties, including but not limited to warranties
of non-infringement, regarding circuits, descriptions and charts stated herein.
Infineon Technologies is an approved CECC manufacturer.
Information
For further information on technology, delivery terms and conditions and prices
please contact the Infineon Technologies offices or our Infineon Technologies
Representatives worldwide - see our webpage at
www.infineon.com/fiberoptics
Infineon Technologies AG • Fiber Optics • Wernerwerkdamm 16 • Berlin D-13623, Germany
Infineon Technologies, Inc. • Fiber Optics • 1730 North First Street • San Jose, CA 95112, USA
Infineon Technologies K.K. • Fiber Optics • Takanawa Park Tower • 20-14, Higashi-Gotanda, 3-chome, Shinagawa-ku • Tokyo 141, Japan
Infineon Technologies AG 2001
Dimensions in (mm) inches
Recommended PCB thickness: max. (2.54) 0.1
(6x)
Circuit Board Layout
10x
0.05
.032 0.04
(0.81 0.1)
M
2.
6x
(13.97)
.550
.055 0.04
(1.4 0.1)
(10x)
Pitch
Min
housing leads
Holes for
- B -
0
M
- A -
(13.59)
.386
(9.8)
.535
Max.
Max.
(3.1)
.12
.472
(12)
- C -
Warnings
Due to technical requirements components may contain dangerous substances.
For information on the types in question please contact your Infineon Technologies
offices.
Infineon Technologies Components may only be used in life-support devices or
systems with the express written approval of Infineon Technologies, if a failure of
such components can reasonably be expected to cause the failure of that
life-support device or system, or to affect the safety or effectiveness of that device
or system. Life support devices or systems are intended to be implanted in the
human body, or to support and/or maintain and sustain and/or protect human life.
If they fail, it is reasonable to assume that the health of the user or other persons
may be endangered.
10 pin module requires only 12 PCB holes.
1.
2.
(7 .75)
.305
(7 .11)
(4.57)
Toleranced to accommodate round or rectangular leads
4 optional package grounding tabs
.28
.18
Tx
Rx
MS2
MS1
(47 .65)
1.875
T1
max.
2x5 Pin Module Top View
2x
(17 .78)
T4
(37 .56)
1.479
.7
.042
(
4x
1.07
2.
max.
+.000
(1.78)
-.004
.070
-0.1
0
)
10 9 8 7 6
1 2 3 4 5
1.
(7 .11)
.280
(3.56)
10x
.14
.024
(
0.61
1.
2.
+.000
T3
T2
-.008
-0.2
4x
0
)
(10.16)
.400
(0.9 max.)
.035 max.
(3.0)
(13.34)
.118
.53