v23809-f7-t10 Infineon Technologies Corporation, v23809-f7-t10 Datasheet - Page 2

• Manufacturer Part Number: v23809-f7-t10
• Description: Multimode 1300 Fibre Channel Transceiver With Connector
• Manufacturer: Infineon Technologies Corporation

DESCRIPTION
This data sheet describes the Infineon Fibre Channel trans-
ceiver, which belongs to the Infineon Multistandard Transceiver
Family. It is fully compliant with the Fibre Channel FC-133
MBaud and FC-266 MBaud standard.
Fibre Channel provides a general transport for upper layer proto-
cols such as Intelligent Peripheral Interface (IPI), High Perfor-
mance Parallel Interface (HIPPI) and Small Computer System
Interface (SCSI) command sets. Defined transmission rates are
266 MBaud and 133 MBaud in point-to-point or fabric topology.
The Infineon low cost multistandard transceiver is a single unit
comprised of a transmitter, a receiver, and an ST receptacle.
This design frees the customer from many alignment and PC
board layout concerns. The modules are designed for low cost
applications.
The inputs/outputs are PECL compatible, and the unit operates
from a 3.0 V to 5.5 V power supply. As an option, the data output
stages can be switched to static levels during absence of light
as indicated by the Signal Detect function. It can be directly in-
terfaced with available chipsets.
Regulatory Compliance
Fiber Optics
Feature
Electromagnetic
Interference (EMI)
Immunity:
Electrostatic
Discharge
Immunity:
Radio Frequency
Electromagnetic
Field
Eye Safety
Standard
FCC Class B
EN 55022 Class B
CISPR 22
EN 61000-4-2
IEC 1000-4-2
EN 61000-4-3
IEC 1000-4-3
IEC 825-1
Comments
Noise frequency
range: 30 MHz to
1 GHz
Discharges of
discharge probe on
the receptacle cause
no damage.
With a field strength
of 10 V/m rms, noise
frequency ranges
from 10 MHz to
1 GHz
Class 1
15kV with an air
2
TECHNICAL DATA
The electro-optical characteristics described in the following
tables are valid only for use under the recommended operating
conditions.
Recommended Operating Conditions
Notes
1. For V
2. To maintain good LED reliability, the device should not be held in the
3. To achieve proper PECL output levels the 50
Parameter
Ambient Temperature
Power Supply Voltage
Supply Current 3.3 V
Supply Current 5 V
Transmitter
Data Input
High Voltage
Data Input
Low Voltage
Threshold Voltage
Input Data Rise/Fall
Time, 20%–80%
Data High Time
Receiver
Output Current
Input Duty Cycle
Distortion
Input Data
Dependent Jitter
Input Random Jitter
Input Center
Wavelength
Electrical
Output Load
(I
45 mA for the three outputs. Load is 50
ON state for more than the specified time. Normal operation should
be done with 50% duty cycle.
be done to V
notes.
CC2
CC
+I
V23809-F7–T10, MM 1300 nm LED Fibre Channel 1x9 Transceiver (ST)
CC3
–V
EE
) does not include the load drive current (I CC1 ). Add max.
(3)
CC
(min., max.). 50% duty cycle. The supply current
(2)
–2 V. For correct termination see the application
(1)
Symbol
T
V
I
V
V
V
t
t
I
t
t
t
R
CC
O
R
ON
DCD
DDJ
RJ
AMB
C
CC
IH
IL
BB
L
, t
–V
–V
–V
–V
F
CC
CC
EE
CC
Min.
0
3
–1165
–1810
–1380
0.4
1260
to V
Typ. Max.
50
CC
termination should
–2 V.
70
5.5
230
260
–880
–1475
–1260
1.3
1000
25
1
1
0.76
1380
Units
V
mA
mV
ns
mA
ns
nm
C