lmp7300max National Semiconductor Corporation, lmp7300max Datasheet - Page 12
![no-image](/images/no-image-200.jpg)
lmp7300max
Manufacturer Part Number
lmp7300max
Description
Micropower Precision Comparator And Precision Reference With Adjustable Hysteresis
Manufacturer
National Semiconductor Corporation
Datasheet
1.LMP7300MAX.pdf
(14 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
lmp7300max/NOPB
Manufacturer:
NS/TI
Quantity:
90
www.national.com
PRECISION HIGH TEMPERATURE SWITCH
The LMP7300 brings accuracy and stability to simple sensor
switch applications. Figure 9 shows the LMP7300 setup in a
high temperature switch configuration. The input bridge es-
tablishes the trip point at 85°C and the reset temperature at
80°C. The comparator is set up with positive hysteresis of
14.3 mV and no negative hysteresis. When the temperature
is rising it trips at 85°C. The 14.3 mV hysteresis allows the
temperature to drop to 80°C before reset.
The temperature sensor used is an Omega 44008 Precision
NTC Thermistor. The 44008 has an accuracy of ±0.2°C. The
resistance at 85°C is 3270.9Ω and at 80°C is 3840.2Ω. The
trip voltage threshold is established by one half of the bridge,
which is the ratio of R
set by the second half, which is the ratio of the thermistor re-
sistance R
∼
The thermistor specification states it has a 1°C/mW dissipa-
MICROPOWER PRECISION BATTERY LOW VOLTAGE
DETECTOR
The ability of the LMP7300 to operate at very low supply volt-
ages, makes it an ideal choice for low battery detection ap-
plication in portable equipment. The circuit in Figure 9
performs the function of low voltage threshold detection in a
3 cell 0.9V discharge voltage, battery monitor application.
R
50 µA bridge current to minimize the power in the thermistor.
1
and R
2
TH
are chosen to set the inverting input voltage equal
and R
SET
ADJ
. The resistance values are chosen for
and R
FIGURE 9. Battery Voltage Monitor for 3 Cell Discharge Voltage
SET
. The input signal bias is
FIGURE 8. Precision High Temperature Switch
12
tion error. The reference voltage establishes the supply volt-
age for the bridge to make the circuit independent of supply
voltage variation. Capacitor C
pole at F
tance values chosen C
This will limit the thermal noise in the bridge.
The accuracy of the circuit can be calculated from the nearest
resistance values chosen. For 1% resistors RADJ is 3.24
kΩ, and R
2.488 mV/C at 85°C. In general, the higher the bridge current
is allowed to be, the higher the bridge gain will be. The actual
trip point found during simulation is 85.3°C and the reset point
is 80.04°C. With the values chosen the worst case trip tem-
perature uncertainty is ±1.451°C and the reset uncertainty is
±1.548°C. Accuracy could be maximized with resistors cho-
sen to 0.1% values, 0.1% tolerance and by using the 0.1%
model of the Omega 44008 thermistor.
to the non-inverting input voltage when the battery voltage is
equal to the minimum operating voltage of the system. Here,
the very precise reference output voltage is directly connect-
ed to the non-inverting input on the comparator and sets an
accurate threshold voltage. The hysteresis is set to 0 mV
negative and 20 mV positive. The output is off for voltages
higher than the minimum V
detects a minimum battery voltage condition.
CORNER
SET
is 78.7 kΩ. The bridge gain becomes
= 1/(2πC
20175647
1
should be selected for Fc < 10 Hz.
BATT
1
*2(R
1
, and turns on when the circuit
establishes a low frequency
SET
20175631
//R
ADJ
)). With the resis-