pi2eqx3231bl Pericom Semiconductor Corporation, pi2eqx3231bl Datasheet - Page 3

• Manufacturer Part Number: pi2eqx3231bl
• Description: 3.0gbps, 1-port, Sata2 I/m Re-driver
• Manufacturer: Pericom Semiconductor Corporation

Maximum Ratings
(Above which useful life may be impaired. For user guide lines, not tested.)
AC/DC Electrical Characteristics
Notes
1.
2.
3. Using Compliance test at 1.5Gbps and 3Gbps. Also using OOB (OOB is formed by ALIGNp primitive or D24.3) test patterns at 1.5Gbps. The
I
P
P
P
P
P
tpd
CML Receiver Input
V
V
V
Z
Z
Equalization
J
J
DD
RS
RM
Storage Temperature ........................................................ –65°C to +150°C
Supply Voltage to Ground Potential ................................... –0.5V to +2.5V
DC SIG Voltage ..........................................................–0.5V to V
Current Output ................................................................-25mA to +25mA
Power Dissipation Continous ......................................................... 500mW
Operating Temperature .............................................................. 0 to +70°C
standby
active18
idle18
active15
idle15
RX-DC
RX-DIFF-DC
RX-DIFFP-P
RX-CM-ACP
TH-SD
Symbol
K28.7 pattern is applied differentially at point A as shown in Figure 1.
Total jitter does not include the signal source jitter. Total jitter (TJ) = (14.1 × RJ + DJ) where RJ is random RMS jitter and DJ is maximum
deterministic jitter. Signal source is a K28.5 ± pattern (00 1111 1010 11 0000 0101) for the deterministic jitter test and K28.7 (0011111000) or
equivalent for random jitter test. Residual jitter is that which remains after equalizing media-induced losses of the environment of Figure 1 or
its equivalent. The deterministic jitter at point B must be from media-induced loss, and not from clock source modulation. JItter is measured at
0V at point C of Figure 1.
ALIGN primitive (K28.5+D10.2+D27.3 = 0011111010+0101010101+0010011100). The D24.3 = 00110011001100110011
08-0328
Power Supply Current
Power, standby
Power, active @ 1.8V
Power, idle @ 1.8V
Power, active @ 1.5V
Power, idle @ 1.5V
Latency
Differential Input Peak-to-
peak Voltage
AC Peak Common Mode
Input Voltage
Signal detect Threshold
DC Input Impedance
DC Differential Input
Impedance
Residual Jitter
Random Jitter
Parameter
(1,2)
(1,2)
(V
EN_[A:B] = 0
VDD=1.8V, EN_[A:B] = 1, Vrx-diff-p >= Vth-sd
VDD=1.8V, EN_[A:B] = 1, Vrx-diff-p < Vth-sd
VDD=1.5V, EN_[A:B] = 1, Vrx-diff-p >= Vth-sd
VDD=1.5V, EN_[A:B] = 1, Vrx-diff-p < Vth-sd
From differential input to differential output
CE = 1
Total Jitter
DD
= 1.4V to 1.9V)
Conditions
3
DD
+0.5V
Note:
Stresses greater than those listed under MAX I MUM RAT-
INGS may cause permanent damage to the de vice. This is
a stress rating only and func tion al op er a tion of the device
at these or any other conditions above those indicated in
the operational sections of this spec i fi ca tion is not implied.
Exposure to absolute max i mum rating con di tions for ex-
tended periods may affect re li abil i ty.
3.0Gbps, 1-Port, SATA2 i/m Re-Driver
0.200
Min.
50
40
80
(2)
Typ.
125
100
100
100
2.0
1.5
80
50
PI2EQX3231BL
200
PS8997B
Max.
160
130
150
120
0.3
90
60
1
(3)
mVppd
psrms
Units
Ulp-p
Ohm
mW
mW
mW
mW
mA
mV
ns
V
12/04/08