pi2dbs212 Pericom Semiconductor Corporation, pi2dbs212 Datasheet - Page 2

• Manufacturer Part Number: pi2dbs212
• Description: 2-channel Broadband 2 1, 1.8v, Mux/demux Switch
• Manufacturer: Pericom Semiconductor Corporation

Maximum Ratings
(Above which useful life may be impaired. For user guide lines, not tested.)
DC Electrical Characteristics for Switching over Operating Range
Notes:
1.
2.
Power Supply Characteristics
Notes:
1.
2.
Dynamic Electrical Characteristics Over the Operating Range
Notes:
1.
Parameters
Storage Temperature....................................–65°C to +150°C
Supply Voltage to Ground Potential...............–0.5V to +2.5V
DC Input Voltage ............................................–0.5V to V
DC Output Current......................................................120mA
Power Dissipation...........................................................0.5W
Paramenter
Parameter
Guaranteed by design. Typical values are at V
For Max. or Min. conditions, use appropriate value specifi ed under Electrical Characteristics for the applicable device type.
Typical values are at V
For Max. or Min. conditions, use appropriate value specifi ed under Electrical Characteristics for the applicable device type.
Typical values are at V
X
I
O
I
LOSS
BW
R
C
DD
TALK
V
V
V
I
I
IRR
IH
ON
ON
07-0243
IL
IH
IK
IL
Quiescent Power Supply Current
Crosstalk
OFF Isolation
Differential Inser-
tion Loss
Bandwidth
Input HIGH Voltage
Input LOW Voltage
Clamp Diode Voltage
Input HIGH Current
Input LOW Current
ON Resistance
Capacitance ON (A/B)
Description
DD
DD
Description
= 1.8V, T
= 1.8V, T
Description
A
A
= 25°C ambient and maximum loading.
= 25°C ambient and maximum loading.
See Fig. 1 for Measurement Setup, f = 1.65
See Fig. 2 for Measurement Setup, f = 1.65
DD
= 1.8V, T
V
V
Guaranteed HIGH level
Guaranteed LOW level
V
V
V
V
40mA
VIN = 0, V
DD
DD
DD
DD
DD
DD
Test Conditions
f = 1.65 GHz
A
= Max., V
= Max., I
= Max., V
= Max., V
= Min., V
= 25°C ambient, and maximum loading.
@ –3 dB
DD
Test Conditions
GHz
GHz
DD
2
1.8V, 1.8GHz, Differential Broadband Signal Switch,
Test Conditions
IN
IN
= 1.8V
Note:
Stresses greater than those listed under MAX I MUM RAT INGS may cause
permanent damage to the de vice. This is a stress rating only and func-
tion al op er a tion of the device at these or any other conditions above those
indicated in the operational sections of this spec i fi ca tion is not implied.
Exposure to absolute max i mum rating con di tions for extended periods
may affect re li abil i ty.
IN
IN
IN
= –18mA
and V
= 1.3V, I
= V
= GND
2-Differential Channel, 2:1 Mux/DeMux Switch
CC
SEL
(1)
IN
(T A = –40º to +85ºC, V DD = 1.8V±10%)
= GND or
=
(1)
(T
A
0.65 x V
= –40°C to +85°C, V
Min.
Min.
–0.5
Min.
DD
Typ.
Typ.
–1.8
–26
–35
–0.7
2.0
3.5
Typ.
(1)
300
(2)
(2)
DD
0.35 x V
Max.
PS8921A
= 1.8V ±10%)
Max.
–1.2
Max.
±5
±5
10
400
PI2DBS212
DD
Units
GHz
Units
dB
Units
Ohm
10/31/07
μA
μA
pF
V