ncp4896 ON Semiconductor, ncp4896 Datasheet
ncp4896
Available stocks
Related parts for ncp4896
ncp4896 Summary of contents
Page 1
... Low. The NCP4896 contains circuitry to prevent from “pop and click” noise that would otherwise occur during turn−on and turn−off transitions also efficient when switching modes from BTL to SE and SE to BTL ...
Page 2
... C b VIH SHUTDOWN SE VIL SE/BTL D Figure 1. Typical NCP4896 Application Circuit with Single−Ended Input PIN DESCRIPTION Pin Type Symbol A1 I SE/BTL When this pin is Low , the audio amplifier is in differential mode High level is applied, the configuration is in Single−Ended Mode ...
Page 3
... C/W with a 500 mm 4. Human Body Model, 100 pF discharge through a 1.5 kW resistor following specification JESD22/A114. 5. Machine Model, 200 pF discharged through all pins following specification JESD22/A115. 6. Maximum ratings per JEDEC Standard JESD78. NCP4896 Symbol Iout ...
Page 4
... Power Supply Rejection Ratio Efficiency Thermal Shutdown Temperature Total Harmonic Distortion 7. Min/Max limits are guaranteed by design, test or statistical analysis. 8. See section “Application Information” for a theoretical approach of this parameter. NCP4896 between − +85 C (Unless otherwise noted). A Symbol Conditions 3 Load ...
Page 5
... Figure 4. THD + N vs. Power Out (BTL Mode 3 BTL Mode = 0 250 mW out 0.01 0.001 10 100 1000 FREQUENCY (Hz) Figure 6. THD + N vs. Frequency (BTL Mode) NCP4896 3 BTL Mode = 1.0 kHz 0.1 0.01 0.001 1000 1200 0 100 Figure 3. THD + N vs. Power Out 1 0.1 0.01 ...
Page 6
... − 200 mV pk−pk ripple −50 −60 −70 −80 −90 −100 10 100 1000 FREQUENCY (Hz) Figure 12. PSRR (BTL Mode 2.6 V NCP4896 10.000 1.000 SE Mode = 1.0 kHz 0.100 0.010 0.001 80 100 0 Figure 9. THD + N vs. Output Power 1.000 ...
Page 7
... W − 200 mV pk−pk ripple −40 −50 −60 −70 −80 −90 −100 10 100 1000 FREQUENCY (Hz) Figure 18. PSRR (SE Mode 3.6 V NCP4896 0 − 3 −20 BTL Mode = 8 W − 200 mV pk−pk ripple −40 −50 −60 −70 −80 =1 ...
Page 8
... 1.1 1 −40 Figure 25. Quiescent Current (SE Mode) vs. VP http://onsemi.com 8 = 200 mV pk−pk GAIN = 5 GAIN = 1 100 1000 10000 100000 FREQUENCY (Hz) NCP4896 ON NCP4896 OFF 100 1000 FREQUENCY ( MODE = − TEMPERATURE (C ) 10000 ...
Page 9
... NCP4896 TYPICAL PERFORMANCE CHARACTERISTICS BTL Mode = Figure 26. Turn On Sequence (BTL Mode 3.6 V http://onsemi.com 9 ...
Page 10
... P = 633 mW Dmax 100 for 100 T , AMBIENT TEMPERATURE ( C) A Figure 31. Power Derating − 9−Pin Flip−Chip CSP NCP4896 0.3 0.25 0.2 0.15 0.1 0. 1.2 0 0.1 Figure 28. Power Dissipation vs. Output Power 0.4 0.35 R 0.3 0.25 0.2 0.15 0.1 0.05 0 0.3 0.4 0 0.05 0.1 Figure 30. Power Dissipation vs. Output Power ...
Page 11
... SE/BTL Operation Due to the internal control of each amplifier through SE/BTL pin, the NCP4896 allows a cost saving for application which requires to drive a example an 8.0 W BTL and Single−Ended load. The internal circuitry avoids “pop and click” noises that could occur in both BTL and Singled− ...
Page 12
... RF set the closed−loop gain of both amplifier order to optimize device and system performance, the NCP4896 should be used in low gain configurations. The low gain configuration minimizes THD + noise values and maximizes the signal to noise ratio, and the amplifier can still be used without running into the bandwidth limitations ...
Page 13
... J12 J13 SHUTDOWN Shutdown Input J20 SE/BTL J8 J10 J11 VP J19 SE/BTL Input C5 100 nF 100 100 kW Figure 33. Typical NCP4896 Application Circuit with Single−Ended Input NCP4896 − OUTA + BYPASS VP VMC BRIDGE 20 kW BIAS CONTROL 20 kW − ...
Page 14
... NCP4896 Silkscreen Layer Top Layer Figure 34. Demonstration Board for 9−Pin Flip−Chip CSP Device − PCB Layers http://onsemi.com Bottom Layer 14 ...
Page 15
... BILL OF MATERIAL Item Part Description 1 NCP4896 Audio Amplifier 2 3.5 mm PCB Jack Connector 3 SMD Resistor SMD Resistor 100 kW 5 SMD Resistor 1.0 kW Ceramic Capacitor 1.0 mF X7R 6 Tantalum Capacitor 47 mF, 6 Ceramic Capcitor 100 nF X7R 9 Jumper Header Vertical Mount, 2*1, 100 mils 10 Jumper Connector, 400 mils 11 I/O Connector ...
Page 16
... MILLIMETERS DIM MIN MAX A 0.540 0.660 A1 0.210 0.270 A2 0.330 0.390 D 1.450 BSC E 1.450 BSC b 0.290 0.340 e 0.500 BSC D1 1.000 BSC E1 1.000 BSC 0.50 mm inches ON Semiconductor Website: http://onsemi.com Order Literature: http://www.onsemi.com/litorder For additional information, please contact your local Sales Representative. NCP4896/D ...