lm21215mhx National Semiconductor Corporation, lm21215mhx Datasheet - Page 19
![no-image](/images/no-image-200.jpg)
lm21215mhx
Manufacturer Part Number
lm21215mhx
Description
15a High Efficiency Synchronous Buck Regulator
Manufacturer
National Semiconductor Corporation
Datasheet
1.LM21215MHX.pdf
(24 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
lm21215mhx/NOPB
Manufacturer:
NSC
Quantity:
2
additional twelve 8 mil. vias under the rest of the device were
used to connect the 4 layers.
Figure 13
vs. output current for the typical application circuit shown in
Figure
PCB LAYOUT CONSIDERATIONS
PC board layout is an important part of DC-DC converter de-
sign. Poor board layout can disrupt the performance of a DC-
DC converter and surrounding circuitry by contributing to EMI,
ground bounce, and resistive voltage loss in the traces. These
can send erroneous signals to the DC-DC converter resulting
in poor regulation or instability.
FIGURE 13. Maximum Ambient Temperature vs. Output
FIGURE 12. Thermal Resistance vs PCB Area (4 Layer
15, assuming a θ
shows a plot of the maximum ambient temperature
125
120
115
110
105
100
30
28
26
24
22
20
18
16
14
12
10
95
90
85
80
2
0
3
Current (0 LFM)
OUTPUT CURRENT (A)
3
JA
4
BOARD AREA (in 2 )
Board)
value of 24 °C/W.
5
6
6
9
7
8
12
9
15
10
30103742
30103744
19
Good layout can be implemented by following a few simple
design rules.
1. Minimize area of switched current loops. In a buck regulator
there are two loops where currents are switched at high slew
rates. The first loop starts from the input capacitor, to the reg-
ulator PVIN pin, to the regulator SW pin, to the inductor then
out to the output capacitor and load. The second loop starts
from the output capacitor ground, to the regulator GND pins,
to the inductor and then out to the load (see
minimize both loop areas, the input capacitor should be
placed as close as possible to the VIN pin. Grounding for both
the input and output capacitor should be close. Ideally, a
ground plane should be placed on the top layer that connects
the PGND pins, the exposed pad (EP) of the device, and the
ground connections of the input and output capacitors in a
small area near pin 10 and 11 of the device. The inductor
should be placed as close as possible to the SW pin and out-
put capacitor.
2. Minimize the copper area of the switch node. The six SW
pins should be routed on a single top plane to the pad of the
inductor. The inductor should be placed as close as possible
to the switch pins of the device with a wide trace to minimize
conductive losses. The inductor can be placed on the bottom
side of the PCB relative to the LM21215, but care must be
taken to not allow any coupling of the magnetic field of the
inductor into the sensitive feedback or compensation traces.
3. Have a solid ground plane between PGND, the EP and the
input and output cap. ground connections. The ground con-
nections for the AGND, compensation, feedback, and soft-
start components should be physically isolated (located near
pin 1 and 20) from the power ground plane but a separate
ground connection is not necessary. If not properly handled,
poor grounding can result in degraded load regulation or er-
ratic switching behavior.
4. Carefully route the connection from the VOUT signal to the
compensation network. This node is high impedance and can
be susceptible to noise coupling. The trace should be routed
away from the SW pin and inductor to avoid contaminating
the feedback signal with switch noise.
5. Make input and output bus connections as wide as possi-
ble. This reduces any voltage drops on the input or output of
the converter and can improve efficiency. Voltage accuracy
at the load is important so make sure feedback voltage sense
is made at the load. Doing so will correct for voltage drops at
the load and provide the best output accuracy.
6. Provide adequate device heatsinking. For most 15A de-
signs a four layer board is recommended. Use as many vias
as is possible to connect the EP to the power plane heatsink.
The vias located underneith the EP will wick solder into them
if they are not filled. Complete solder coverage of the EP to
the board is required to achieve the θ
the previous section. Either an adequate amount of solder
must be applied to the EP pad to fill the vias, or the vias must
be filled during manufacturing. See the Thermal Considera-
tions section to ensure enough copper heatsinking area is
used to keep the junction temperature below 125°C.
JA
values described in
Figure
www.national.com
14). To