lmc6062imx National Semiconductor Corporation, lmc6062imx Datasheet - Page 10
![no-image](/images/no-image-200.jpg)
lmc6062imx
Manufacturer Part Number
lmc6062imx
Description
Precision Cmos Dual Micropower Operational Amplifier
Manufacturer
National Semiconductor Corporation
Datasheet
1.LMC6062IMX.pdf
(15 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LMC6062IMX
Manufacturer:
TI/德州仪器
Quantity:
20 000
Company:
Part Number:
lmc6062imx/NOPB
Manufacturer:
NS
Quantity:
9 328
Part Number:
lmc6062imx/NOPB
Manufacturer:
NS/国半
Quantity:
20 000
www.national.com
Applications Hints
PRINTED-CIRCUIT-BOARD LAYOUT
FOR HIGH-IMPEDANCE WORK
It is generally recognized that any circuit which must operate
with less than 1000 pA of leakage current requires special
layout of the PC board. When one wishes to take advantage
of the ultra-low bias current of the LMC6062, typically less
than 10 fA, it is essential to have an excellent layout. Fortu-
nately, the techniques of obtaining low leakages are quite
simple. First, the user must not ignore the surface leakage of
the PC board, even though it may sometimes appear accept-
ably low, because under conditions of high humidity or dust
or contamination, the surface leakage will be appreciable.
To minimize the effect of any surface leakage, lay out a ring
of foil completely surrounding the LMC6062’s inputs and the
terminals of capacitors, diodes, conductors, resistors, relay
terminals etc. connected to the op-amp’s inputs, as in Figure
4 . To have a significant effect, guard rings should be placed
on both the top and bottom of the PC board. This PC foil
must then be connected to a voltage which is at the same
voltage as the amplifier inputs, since no leakage current can
flow between two points at the same potential. For example,
a PC board trace-to-pad resistance of 10
mally considered a very large resistance, could leak 5 pA if
the trace were a 5V bus adjacent to the pad of the input. This
would cause a 100 times degradation from the LMC6062’s
actual performance. However, if a guard ring is held within
5 mV of the inputs, then even a resistance of 10
cause only 0.05 pA of leakage current. See Figure 5 for
typical connections of guard rings for standard op-amp con-
figurations.
FIGURE 4. Example of Guard Ring in P.C. Board
Layout
(Continued)
12
, which is nor-
11
01129806
would
10
The designer should be aware that when it is inappropriate
to lay out a PC board for the sake of just a few circuits, there
is another technique which is even better than a guard ring
on a PC board: Don’t insert the amplifier’s input pin into the
board at all, but bend it up in the air and use only air as an
insulator. Air is an excellent insulator. In this case you may
have to forego some of the advantages of PC board con-
struction, but the advantages are sometimes well worth the
effort of using point-to-point up-in-the-air wiring. See Figure
6 .
Latchup
CMOS devices tend to be susceptible to latchup due to their
internal parasitic SCR effects. The (I/O) input and output pins
look similar to the gate of the SCR. There is a minimum
current required to trigger the SCR gate lead. The LMC6062
and LMC6082 are designed to withstand 100 mA surge
current on the I/O pins. Some resistive method should be
used to isolate any capacitance from supplying excess cur-
rent to the I/O pins. In addition, like an SCR, there is a
minimum holding current for any latchup mode. Limiting
current to the supply pins will also inhibit latchup suscepti-
bility.
FIGURE 5. Typical Connections of Guard Rings
(b) Non-Inverting Amplifier
(a) Inverting Amplifier
(c) Follower
01129809
01129807
01129808