at27bv400 ATMEL Corporation, at27bv400 Datasheet
at27bv400
Related parts for at27bv400
at27bv400 Summary of contents
Page 1
... Commercial and Industrial Temperature Ranges Description The AT27BV400 is a high performance low-power, low-voltage 4,194,304-bit one time programmable read only memory (OTP EPROM) organized as either 256K 512K by 8 bits. It requires only one supply in the range of 2.7 to 3.6V in normal read Pin Configurations ...
Page 2
... O15/A-1 pin is used for O15 data output. When BYTE/V PP byte wide organization is selected and the O15/A-1 pin is used for the address pin A-1. When the AT27BV400 is logi- cally regarded as x16 (word-wide), but read in the byte- wide mode, then with A-1= V the lower 8 bits of the 16-bit ...
Page 3
Absolute Maximum Ratings* Temperature Under Bias ................................ - +125 C Storage Temperature ..................................... - +150 C Voltage on Any Pin with with Respect to Ground ..................................-2.0V to +7.0V Voltage on A9 with Respect to Ground ......................................-2.0V ...
Page 4
... SB2 MHz mA OUT 2 -400 and removed simultaneously or after V PP except during programming. The supply current would then be the sum AT27BV400 - 2.7V to 3.6V 2.7V to 3.6V 5V 10% 5V 10% Min Max 1 ...
Page 5
... ST t BYTE Low to Output Transition STD Notes: 1. 2,3,4,5. See the AC Waveforms for Read Operation diagram. Byte-Wide Read Mode AC Waveforms Note: BYTE Word-Wide Read Mode AC Waveforms Note: BYTE AT27BV400 -12 Condition Min Max 120 120 120 50 -15 ...
Page 6
... Pin Capaticance ( MHz OUT Note: 1. Typical values for nominal supply voltage. This parameter is only sampled and is not 100% tested. AT27BV400 after the falling edge of CE without impact after the address is valid without impact on t ACC ...
Page 7
... Programming Waveforms Notes: 1. The Input Timing reference is 0.8V for and t are characteristics of the device but must be accommodated by the programmer. OE DFP 3. When programming the AT27BV400, a 0.1 F capacitor is required across V DC Programming Characteristics ± 5° 6.5 ± 0.25V Symbol Parameter I Input Load Current ...
Page 8
... A0 O15 Codes O7 Manufacturer 0 0 Device Type 1 1 Note: 1. The AT27BV400 has the same Product Identification Code as the AT27C400. Both are programming compatible. AT27BV400 8 = 13.0 ± 0.25V PP Test Conditions Input Rise and Fall Times: (10 Input Pulse Levels: 0.45V to 2.4V (2) Input Timing Reference Level: ...
Page 9
Rapid Programming Algorithm pulse width is used to program. The address is set to the first location raised to 6.5V and BYTE raised to 13.0V. Each address is first programmed with one ...
Page 10
... Package AT27BV400-12JC 44J AT27BV400-12RC 44R AT27BV400-12TC 48T AT27BV400-12JI 44J AT27BV400-12RI 44R AT27BV400-12TI 48T AT27BV400-15JC 44J AT27BV400-15RC 44R AT27BV400-15TC 48T AT27BV400-15JI 44J AT27BV400-15RI 44R AT27BV400-15TI 48T Package Type Operation Range Commercial ( Industrial (- Commercial ( Industrial (- ...
Page 11
Packaging Information 44R, 44-Lead, 0.450" Wide, Plastic Gull Wing Small Outline Package (SOIC) Dimensions in Inches and (Millimeters) 44J, 44-Lead, Plastic J-Leaded Chip Carrier (PLCC) Dimensions in Inches and (Millimeters) JEDEC STANDARD MS-018 AC .045(1.14) X 45° PIN NO. 1 ...