at28lv010 ATMEL Corporation, at28lv010 Datasheet
at28lv010
Available stocks
Related parts for at28lv010
at28lv010 Summary of contents
Page 1
... When the device is deselected, the CMOS standby current is less than 20 µA. The AT28LV010 is accessed like a Static RAM for the read or write cycle without the need for external components. The device contains a 128-byte page register to allow writing 128 bytes simultaneously ...
Page 2
... TSOP Top View A11 A14 A13 A14 28 A13 VCC 25 A11 A16 23 A10 A15 22 CE A12 AT28LV010 VCC A16 A15 A12 4 29 A14 A13 A11 A3 9 ...
Page 3
... Read The AT28LV010 is accessed like a Static RAM. When CE and OE are low and WE is high, the data stored at the memory location determined by the address pins is asserted on the outputs. The outputs are put in the high impedance state when either high. This dual-line control gives designers flexibility in preventing bus contention in their system ...
Page 4
... DATA Polling The AT28LV010 features DATA Polling to indicate the end of a write cycle. During a byte or page write cycle an attempted read of the last byte written will result in the complement of the written data to be presented on I/O7. Once the write cycle has been completed, true data is valid on all outputs, and the next write cycle may begin ...
Page 5
... MHz mA 3.6V OUT 1 -100 µ 3. AT28LV010 AT28LV010-25 -40°C - 85°C 3.3V ± 10 High High Z Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent dam- age to the device. This is a stress rating only and ...
Page 6
... whichever occurs first ( This parameter is characterized and is not 100% tested. AT28LV010 6 (1)(2)(3)( after the address transition without impact on t ACC after the falling edge of CE without impact pF). L AT28LV010-20 Min Max Units 200 ns 200 ...
Page 7
... Input Test Waveforms and Measurement Level 12. Output Test Load 13. Pin Capacitance ( MHz 25°C Symbol Typ OUT Note: 1. This parameter is characterized and is not 100% tested. 0395D–PEEPR–10/ < Max 6 12 AT28LV010 Units Conditions OUT 7 ...
Page 8
... CH t Write Pulse Width ( Data Set-up Time Data, OE Hold Time DH OEH Note: 1. All write operations must be preceded by the SDP command sequence. 15. AC Write Waveforms 15.1 WE Controlled 15.2 CE Controlled AT28LV010 8 (1) Min Max Units 0 ns 100 200 ns 100 0395D– ...
Page 9
... ADDRESS 5555 LOAD DATA 55 TO ADDRESS 2AAA LOAD DATA A0 TO ADDRESS 5555 (2) WRITES ENABLED LOAD DATA XX TO ANY ADDRESS (3) LOAD LAST BYTE TO (3) LAST ADDRESS ENTER DATA PROTECT STATE AT28LV010 Min Max 10 0 100 100 10 200 150 100 (1)(2)(3) Units µ ...
Page 10
... These parameters are characterized and not 100% tested. 2. See AC Read Characteristics 22. Toggle Bit Waveforms Notes: 1. Toggling either both OE and CE will operate toggle bit. 2. Beginning and ending state of I/O6 will vary. 3. Any address location may be used but the address should not vary. AT28LV010 10 (1) Min 10 10 (1) ...
Page 11
... Die Products Reference Section: Parallel EEPROM Die Products 0395D–PEEPR–10/06 (1) Ordering Code AT28LV010-20JI AT28LV010-20PI AT28LV010-20TI AT28LV010-25JI AT28LV010-25PI AT28LV010-25TI Ordering Code AT28LV010-20JU AT28LV010-20PU AT28LV010-20TU Package Type Package and Temperature Combinations JI, JU, PI, TI, TU, PU AT28LV010 Package Operation Range 32J Industrial 32P6 (-40° to 85° C) ...
Page 12
... Allowable protrusion is .010"(0.254 mm) per side. Dimension D1 and E1 include mold mismatch and are measured at the extreme material condition at the upper or lower parting line. 3. Lead coplanarity is 0.004" (0.102 mm) maximum. 2325 Orchard Parkway San Jose, CA 95131 R AT28LV010 12 1.14(0.045) X 45˚ PIN NO. 1 IDENTIFIER E1 E ...
Page 13
... Mold Flash or Protrusion shall not exceed 0.25 mm (0.010"). 2325 Orchard Parkway San Jose, CA 95131 R 0395D–PEEPR–10/06 D PIN 0º ~ 15º REF eB TITLE 32P6, 32-lead (0.600"/15.24 mm Wide) Plastic Dual Inline Package (PDIP) AT28LV010 E1 A1 COMMON DIMENSIONS (Unit of Measure = mm) MIN SYMBOL NOM A – – A1 0.381 – D 41.783 – ...
Page 14
... This package conforms to JEDEC reference MO-142, Variation BD. 2. Dimensions D1 and E do not include mold protrusion. Allowable protrusion 0.15 mm per side and 0.25 mm per side. 3. Lead coplanarity is 0.10 mm maximum. 2325 Orchard Parkway San Jose, CA 95131 R AT28LV010 14 PIN SEATING PLANE ...
Page 15
... Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. © 2006 Atmel Corporation. All rights reserved. Atmel marks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. Atmel Operations Memory ...