at17lv002a-10q1 ATMEL Corporation, at17lv002a-10q1 Datasheet
at17lv002a-10q1
Related parts for at17lv002a-10q1
at17lv002a-10q1 Summary of contents
Page 1
... Replacement for AT17C/LV002A Description The AT17C002A and AT17LV002A (high-density AT17A Series) FPGA Configuration EEPROMs (configurators) provide an easy-to-use, cost-effective configuration mem- ory for programming Altera FLEX devices. The AT17A Series is packaged in the popular 20-lead PLCC and the 32-lead TQFP. The AT17A Series family uses a simple serial-access procedure to configure one or more FPGA devices ...
Page 2
Pin Configuration 20-lead PLCC DCLK 4 WP1 Block Diagram SER_EN WP1 OSC CONTROL OSC POWER-ON RESET DCLK READY AT17C/LV002A 2 18 SER_EN READY 14 NC PROGRAMMING MODE LOGIC ...
Page 3
Device The control signals for the configuration EEPROM (nCS, OE and DCLK) interface directly with the FPGA device control signals. All FPGA devices can control the entire configuration pro- Configuration cess and retrieve data from the configuration EEPROM without requiring ...
Page 4
Figure 1. Configuration with a Single AT17A Series Configurator EPF6K/EPF10K DCLK nCONFIG m 0.1 F DATA0 nCE CONF_DONE MSEL0 nSTATUS MSEL1 GND Notes: 1. Use of the READY pin is optional. 2. Introducing an RC ...
Page 5
The READY pin is available as an open-collector indicator of the device’s reset status driven Low while the device is in its power-on reset cycle and released (tri-stated) when the cycle is complete. It can be used to ...
Page 6
Pin Configurations 20 32 PLCC TQFP Pin Pin Name I DATA I DCLK I WP1 nCS GND 12 15 nCASC ...
Page 7
... These are stress ratings only, and functional operation of the device at these or any other conditions beyond those listed under +0.5V Operating Conditions is not implied. Exposure to CC Absolute Maximum Ratings conditions for extended periods of time may affect device reliability. AT17C002A Min 4.75 4.5 4.5 AT17LV002A Max Min Max Units 5.25 3.15 3.45 V 5.5 3.15 3.45 V 5.5 3 ...
Page 8
DC Characteristics ± 5% Commercial/5V ± 10% Industry/Military CC Symbol Description V High-level Input Voltage IH V Low-level Input Voltage IL V High-level Output Voltage ( Low-level Output Voltage ( High-level Output Voltage ...
Page 9
AC Characteristics nCS OE DCLK DATA AC Characteristics When Cascading OE nCS DCLK T CDF DATA LAST BIT T OCK nCASL 2280B–08/01 T SCE CAC T OCE T SCE T T ...
Page 10
AC Characteristics for AT17C002A ± 5% Commercial ± 10% Industry/Military CC CC Symbol Description ( Data Delay OE (2) T nCS to Data Delay CE (2) T DCLK to Data Delay ...
Page 11
... DCLK High Time Master Mode HC Notes: 1. Preliminary specifications for military operating range only test load = 50 pF. 3. Float delays are measured with loads. Transition is measured ± 200 mV from steady state active levels. AC Characteristics for AT17LV002A When Cascading V = 3.3V ± 5% Commercial Symbol ...
Page 12
... AT17LV002A-10JC AT17LV002A-10JI (1) 2-Mbit AT17LV002A-10QC AT17LV002A-10Q1 Note: 1. Use 2-Mbit density parts to replace Altera EPC2. Atmel AT127C/LV002A devices do not support JTAG programming; Atmel AT17X002A devices use a 2-wire serial interface for in-system programming. 20-lead, Plastic J-leaded Chip Carrier (PLCC) 20J 32-lead, Thin (1.0 mm) Plastic Gull Wing Quad Flat Package (TQFP) ...
Page 13
Packaging Information 20J, 20-lead, Plastic J-leaded Chip Carrier (PLCC) Dimensions in Inches and (Millimeters) JEDEC STANDARD MS-018 AA AT17C/LV002A 13 32A, 32-lead, Thin (1.0 mm) Plastic Gull Wing Quad Flat Package (TQFP) Dimensions in Millimeters and (Inches) PIN 1 ID ...
Page 14
... Atmel Corporation 2001. Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company’s standard warranty which is detailed in Atmel’s Terms and Conditions located on the Company’s web site. The Company assumes no responsibility for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does not make any commitment to update the information contained herein ...