viper50b STMicroelectronics, viper50b Datasheet - Page 12
![no-image](/images/manufacturer_photos/0/6/637/stmicroelectronics_sml.jpg)
viper50b
Manufacturer Part Number
viper50b
Description
Smps Primary I.c.
Manufacturer
STMicroelectronics
Datasheet
1.VIPER50B.pdf
(20 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
VIPER50B
Manufacturer:
ST
Quantity:
20 000
VIPER50B/BSP
OPERATION DESCRIPTION :
CURRENT MODE TOPOLOGY:
The current mode control method, like the one
integrated in the VIPer50B/BSP uses two control
loops - an inner current control loop and an outer
loop for voltage control. When the Power
MOSFET output transistor is on, the inductor
current (primary side of the transformer) is
monitored with a SenseFET technique and
converted into a voltage V
current. When V
output voltage error) the power switch is switched
off. Thus, the outer voltage control loop defines
the level at which the inner loop regulates peak
current through the power switch and the primary
winding of the transformer.
Excellent open loop D.C. and dynamic line
regulation is ensured due to the inherent input
voltage feedforward characteristic of the current
mode control. This results in an improved line
regulation, instantaneous correction to
changes and better stability for the voltage
regulation loop.
Current mode topology also ensures good
limitation in the case of short circuit. During a first
phase the output current increases slowly
following the dynamic of the regulation loop. Then
it reaches the maximum limitation current
internally set and finally stops because the power
supply on V
applications the maximum peak current internally
set can be overridden by externally limiting the
voltage excursion on the COMP pin. An
integrated blanking filter inhibits the PWM
comparator output for a short time after the
integrated Power MOSFET is switched on. This
function prevents anomalous or premature
termination of the switching pulse in the case of
current
capacitance or secondary side rectifier reverse
recovery time.
STAND-BY MODE
Stand-by operation in nearly open load condition
automatically leads to a burst mode operation
allowing voltage regulation on the secondary
side. The transition from normal operation to
burst mode operation happens for a power P
given by :
P
12/20
STBY
1
2
spikes
L
P
DD
I
2
STBY
is no longer correct. For specific
S
reaches V
F
caused
SW
S
COMP
by
proportional to this
primary
(the amplified
STBY
side
line
Where:
L
F
I
corresponding to the minimum on time that the
device is able to provide in normal operation. This
current can be computed as :
I
t
propagation time of the internal current sense
and comparator, and represents roughly the
minimum on time of the device. Note that P
may be affected by the efficiency of the converter
at low load, and must include the power drawn on
the primary auxiliary voltage.
As soon as the power goes below this limit, the
auxiliary secondary voltage starts to increase
above the 13V regulation level forcing the output
voltage of the transconductance amplifier to low
state (V
the shutdown mode where the power switch is
maintained in the off state, resulting in missing
cycles and zero duty cycle. As soon as V
back to the regulation level and the V
threshold is reached, the device operates again.
The above cycle repeats indefinitely, providing a
burst mode of which the effective duty cycle is
much lower than the minimum one when in
normal operation. The equivalent switching
frequency is also lower than the normal one,
leading to a reduced consumption on the input
mains lines. This mode of operation allows the
VIPer50B/BSP to meet the new German ”Blue
Angel” Norm with less than 1W total power
consumption for the system when working in
stand-by. The output voltage remains regulated
around the normal level, with a low frequency
ripple corresponding to the burst mode. The
amplitude of this ripple is low, because of the
output capacitors and of the low output current
drawn in such conditions.The normal operation
resumes automatically when the power get back
to higher levels than P
HIGH
SOURCE
An integrated high voltage current source
provides a bias current from the DRAIN pin
during the start-up phase. This current is partially
absorbed by internal control circuits which are
STBY
STBY
b
P
SW
+ t
is the primary inductance of the transformer.
is the normal switching frequency.
d
is the sum of the blanking time and of the
is the minimum controllable current,
COMP
t
b
VOLTAGE
L
t
d
P
< V
V
IN
COMPth
STBY
START-UP
). This situation leads to
.
CURRENT
DD
COMPth
STBY
gets