ncp1396a ON Semiconductor, ncp1396a Datasheet
ncp1396a
Available stocks
Related parts for ncp1396a
ncp1396a Summary of contents
Page 1
... NCP1396A, NCP1396B High Performance Resonant Mode Controller featuring High-Voltage Drivers The NCP1396 A/B offers everything needed to build a reliable and rugged resonant mode power supply. Its unique architecture includes a 500 kHz Voltage Controlled Oscillator whose control mode brings flexibility when an ORing function is a necessity, e.g. in multiple feedback paths implementations. Thanks to its proprietary high− ...
Page 2
HV R17 FB OVP U2A U3A Fast Input fmax C10 C9 C8 R19 R9 R14 R18 R13 R6 Soft− Timer Skip BO DT start Selection PIN FUNCTION DESCRIPTION Pin No. Pin ...
Page 3
Vdd Vdd Imin Vfb ≤ Vfb_off Vref Vref Rt IDT Imax for Vfb = 5 for Vfb < Vfb_min Vdd Imax Vfb = 5 Vdd Vref Itimer Fmax If FAULT Itimer else 0 ...
Page 4
MAXIMUM RATINGS Rating High Voltage bridge pin, pin 14 Floating supply voltage High side output voltage Low side output voltage Allowable output slew rate Power Supply voltage, pin 12 Maximum voltage, all pins (except pin 11 and 10) Thermal Resistance ...
Page 5
ELECTRICAL CHARACTERISTICS (For typical values T = 25°C, for min/max values T J Characteristic SUPPLY SECTION Turn−on threshold level, Vcc going up – A version Turn−on threshold level, Vcc going up – B version Minimum operating voltage after turn−on Startup ...
Page 6
ELECTRICAL CHARACTERISTICS (For typical values T = 25°C, for min/max values T J TIMERS Characteristic Timer charge current Timer duration with capacitor and resistor Timer recurrence in permanent fault, same values as above Voltage ...
Page 7
TYPICAL CHARACTERISTICS − A VERSION 13.55 13.5 13.45 13.4 13.35 13.3 13.25 13.2 13.15 13.1 −40 −25 − TEMPERATURE (°C) Figure 3. V CC(on) 60.2 60.1 60.0 59.9 59.8 59.7 59.6 59.5 59.4 −40 −25 −10 ...
Page 8
TYPICAL CHARACTERISTICS − A VERSION −40 −25 − TEMPERATURE (°C) Figure 9. Source Resistance (ROH) 109 108 107 106 105 104 103 102 101 100 99 ...
Page 9
TYPICAL CHARACTERISTICS − A VERSION 1.045 1.040 1.035 1.030 1.025 1.020 −40 −25 − TEMPERATURE (°C) Figure 15. Brown−Out Reference (VBO) 26.8 26.6 26.4 26.2 26.0 25.8 25.6 25.4 25.2 25 110 125 ...
Page 10
TYPICAL CHARACTERISTICS − B VERSION 10.65 10.60 10.55 10.50 10.45 10.40 10.35 −40 −25 − TEMPERATURE (°C) Figure 17. V CC(on) 60.1 60.0 59.9 59.8 59.7 59.6 59.5 59.4 59.3 −40 −25 − ...
Page 11
TYPICAL CHARACTERISTICS − B VERSION −40 −25 − TEMPERATURE (°C) Figure 23. Source Resistance (ROH) 108 107 106 105 104 103 102 101 100 99 98 ...
Page 12
TYPICAL CHARACTERISTICS − B VERSION 1.050 1.045 1.040 1.035 1.030 1.025 −40 −25 − TEMPERATURE (°C) Figure 29. Brown−Out Reference (VBO) 107 106 105 104 103 102 101 100 110 125 −40 ...
Page 13
... Skip cycle possibility: The absence of soft−start on the NCP1396A fast fault input offers an easy way to implement skip cycle when power saving features are necessary. A simple resistive connection from the feedback pin to the fast fault input, and skip can be implemented. • ...
Page 14
B is more recommended for industrial / medical applications where auxiliary supply directly powers the chip. 2. The A version does not activate the soft−start ...
Page 15
11 100 k 2 8.7 k Figure 32. The OPAMP Arrangement Limits the VCO Modulation Signal between 0.5 and 2.3 V This techniques allows us to detect a fault on the ...
Page 16
RFmin (kW) Figure 36. Minimum Switching Frequency Resistor Selection (Fmin = 100 kHz to 500 kHz) 100 ...
Page 17
Vdd Icharge: Fsw min + Fsw max + − Idis V−1 V Vref DT RDT Figure 40. Dead−time Generation http://onsemi.com Clk ...
Page 18
... The fast fault input undergoes a special treatment. Since we want to implement skip cycle through the fast fault input on the NCP1396A, we cannot activate the soft−start every time the feedback pin stops the operations in low power mode. Therefore, when the fast fault pin is released, over the VCO lead as soon as the output voltage has reached the target ...
Page 19
Clock Pulses 12.0 8.00 4.00 0 8.00 4.00 0 −4.00 A − B −8.00 56.2 m Brown−Out Protection The Brown−Out circuitry (BO) offers a way to protect the resonant converter from low DC input ...
Page 20
Figure 45. Simulation Results for 350 / 250 ON / OFF Levels To the contrary, when the internal BO signal is high (Mlower and Mupper pulse), the IBO ...
Page 21
On Figure 46 blocked and does not bother the BO measurement as long as the NTC and the optocoupler are not activated. As soon as the secondary optocoupler senses an OVP condition, or the NTC reacts to a ...
Page 22
VtimerON level (4 V typical), then all pulses are stopped. If the fault input signal is still present, then the controller permanently stays off and the voltage on the timer capacitor does not move (Itimer is on and ...
Page 23
V CC(on) V CC(min 0.6 V A& Timer Figure 50. At power on, output A is first activated and the frequency slowly decreases via the soft−start capacitor Figure 50 depicts ...
Page 24
... ORDERING INFORMATION Device NCP1396ADR2G NCP1396BDR2G NCP1396APG NCP1396BPG †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specification Brochure, BRD8011/D. for the direct a connection from source. Thanks to this NCP1396B, simple ON/OFF operation is therefore feasible. The High− ...
Page 25
0. 15X C SEATING PLANE 15X 0.58 PACKAGE DIMENSIONS SOIC−16 NB, LESS PIN 13 CASE 751AM−01 ISSUE 15X 0. ...
Page 26
... D 15X 0.010 (0.25) Note: The product described herein (NCP1396A/B), is covered by U.S. patent: 6,097, 075; 7176723; 6,362, 067. There may be some other patent pending. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “ ...