lt3645 Linear Technology Corporation, lt3645 Datasheet - Page 9

• Manufacturer Part Number: lt3645
• Description: 36v 500ma Step-down Regulator And 200ma Ldo
• Manufacturer: Linear Technology Corporation

OPERATION
The LT3645 includes a constant frequency, current mode
step-down buck switching regulator together with a low-
dropout regulator (LDO).
If EN/UVLO is less than ~0.7V, both the buck and LDO
are off, the output is disconnected and the input current
is less than 2μA. The buck turns on when EN/UVLO is
greater than 1.23V. An undervoltage lockout (UVLO)
turns the buck and LDO off when V
An overvoltage lockout (OVLO) turns the buck and LDO
off when V
nonrepetitive one second input voltage transients up to
55V. An internal thermal shutdown circuit monitors the die
temperature and shuts both the buck and LDO off if the
die temperature exceeds ~160°C. The thermal shutdown
has 10 degrees of hysteresis.
An internal regulator provides power to the control circuitry
and produces the 0.8V feedback voltage for the buck and
LDO error amplifi ers.
An internal, fi xed-frequency oscillator in the step-down
regulator enables an RS flip-flop, turning on the internal
power switch Q1. A comparator monitors the current
flowing between the V
off when this current reaches a level determined by the
voltage at V
amplifier servos the V
resistor divider between OUT and ground is tied to the
V
The positive input to the error amp is a 0.8V reference, so
the voltage loop forces the V
voltage of the buck error amplifi er is ramped over 900μs
during the soft-start period. When V
increase in output current, and when V
less output current. Current limit is provided by an active
clamp on the V
FB
pin and presented to the negative error amp input.
IN
C
and the internal slope-compensation. An error
is greater than 38.5V. The part will withstand
C
node.
IN
C
node. The output of an external
and SW pins, turning the switch
FB
pin to 0.8V. The reference
C
IN
rises, it results in an
C
is less than 3.4V.
falls, it results in
The buck power switch (Q1) is driven from the BOOST
pin. An external capacitor and internal diode are used to
generate a voltage at the BOOST pin that is higher than the
input supply, which allows the driver to fully saturate the
internal bipolar NPN power switch for effi cient operation.
An external diode can be used to make the BOOST drive
more effective at low output voltages.
The oscillator reduces the LT3645’s operating frequency
during the soft-start period. This frequency foldback helps
to control the output current during startup.
The current in the external catch diode (D1) is sensed
through the DA pin. If the catch diode current exceeds
0.9A, the oscillator frequency is decreased. This prevents
current runaway during startup or overload.
The LDO only operates if EN/UVLO is greater than 1.23V
and EN2 is greater than 1.3V. If EN/UVLO is low and EN2
is high, the LDO will not start. When EN2 > 1.3V and EN/
UVLO > 1.23V, the LDO power transistor will turn on and
regulate the output at the OUT2 pin. An error amplifi er
driving Q2 has its positive input at the 0.797V reference.
The output of an external resistor divider between OUT2
and ground is tied to the V
negative error amp input, forcing the V
The reference voltage of the LDO error amplifi er is ramped
over 600μs during the soft-start period. The LDO power
transistor (Q2) is driven from the V
NPN which draws its collector current from the V
The NPG pin is an open-collector output that indicates
when both buck and LDO outputs are in at least 90% in
regulation. When FB and FB2 rise above 720mV, the NPG
pin is pulled low.
FB2
pin and presented to the
IN
pin. Q2 is a bipolar
FB2
pin to 0.797V.
LT3645
CC2
pin.
9
3645f