lm5067mmx-2 National Semiconductor Corporation, lm5067mmx-2 Datasheet - Page 20
![no-image](/images/no-image-200.jpg)
lm5067mmx-2
Manufacturer Part Number
lm5067mmx-2
Description
Negative Hot Swap / Inrush Current Controller With Power Limiting
Manufacturer
National Semiconductor Corporation
Datasheet
1.LM5067MMX-2.pdf
(24 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
lm5067mmx-2/NOPB
Manufacturer:
TI
Quantity:
4 500
www.national.com
PC Board Guidelines
The following guidelines should be followed when designing
the PC board for the LM5067:
•
•
•
•
•
Thermal Considerations
The LM5067 should be operated so that its junction temper-
ature does not exceed 125°C. The junction temperature is
equal to:
where T
resistance of the LM5067. P
the LM5067, calculated from:
where I
the R
Place the LM5067 close to the board’s input connector to
minimize trace inductance from the connector to the FET.
Place R
transients below the Absolute Maximum rating of the
LM5067. Transients of several volts can easily occur when
the load current is shut off.
The sense resistor (R
and connected to it using the Kelvin techniques shown in
Figure 7.
The high current path from the board’s input to the load,
and the return path (via Q1), should be parallel and close
to each other wherever possible to minimize loop
inductance.
The VEE connection for the various components around
the LM5067 should be connected directly to each other,
and to the LM5067’s VEE pin, and then connected to the
system VEE at one point. Do not connect the various
components to each other through the high current VEE
track.
IN
CC
A
resistor). The following table provides values for
is the ambient temperature, and R
is the current into the VCC pin (the current through
IN
and C
IN
T
J
close to the VCC and VEE pins to keep
= T
P
D
S
) should be close to the LM5067,
A
= 13V x I
+ (R
D
is the power dissipated within
θJA
CC
x P
FIGURE 17. Suggested Board Connector Design
D
)
θJA
is the thermal
20
•
•
•
R
and 4 layer PC boards, and various number of heat transfer-
ring vias beneath the IC package. It is obvious that adding just
one via to other heat dissipating layers in the PC board affects
R
posed pad on the bottom should be soldered to a copper
plane, and that plane should extend out from beneath the IC
package as well as be connected to exposed copper on the
board’s other side using as many vias as possible. The ex-
posed pad is internally connected to the IC substrate, and is
at VEE potential.
θJA
θJA
Provide adequate heat sinking for the series pass device
(Q1) to help reduce thermal stresses during turn-on and
turn-off.
The board’s edge connector can be designed to shut off
the LM5067 as the board is removed, before the supply
voltage is disconnected from the LM5067. In Figure 17 the
voltage at the UVLO/EN pin goes to VEE before V
removed from the LM5067 due to the shorter edge
connector pin. When the board is inserted into the edge
connector, the system voltage is applied to the LM5067’s
VEE and VCC pins before voltage is applied to the UVLO/
EN pin.
If power dissipation within the LM5067 is high, an exposed
copper pad should be provided beneath the package, and
that pad should be connected to exposed copper on the
board’s other side with as many vias as possible. If the LLP
package is used, the exposed pad on the package bottom
should be soldered to the board’s copper pad. The
package’s exposed pad is at the VEE voltage. See the
Thermal Considerations section.
and R
very significantly. If the LLP-10 package is used, the ex-
θJC
for the MSOP-10 and LLP-10 packages, 2 layer
30030962
SYS
is