lx1563 Microsemi Corporation, lx1563 Datasheet - Page 13
![no-image](/images/manufacturer_photos/0/4/446/microsemi_corporation_sml.jpg)
lx1563
Manufacturer Part Number
lx1563
Description
Second-generation Power Factor Controller
Manufacturer
Microsemi Corporation
Datasheet
1.LX1563.pdf
(25 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
lx15631M
Manufacturer:
SHARP
Quantity:
5 510
Company:
Part Number:
lx1563CN
Manufacturer:
ST
Quantity:
5 510
Company:
Part Number:
lx1563IDM
Manufacturer:
Microsemi Analog Mixed Signal
Quantity:
135
Part Number:
lx1563IM
Manufacturer:
LX
Quantity:
20 000
Copyright © 1996
Rev. 1.3a
The operation of the IC is best described by referring to the
block-diagram. The output of the multiplier stage generates a
voltage proportional to the product of the rectified AC line and
the output of the error amplifier. This voltage serves as the
reference for the inductor peak current that is sensed by the
resistor in series with the external power MOSFET. When the
sense voltage exceeds this threshold, C.S. comparator trips and
resets the latch as well as turning the power MOSFET off.
and stored in the output capacitor, causing the inductor current
UNDERVOLTAGE LOCK OUT
The LX1562/63 undervoltage lock-out is designed to maintain
an ultra low quiescent current of less than 300µA, while guar-
anteeing the IC is fully functional before the output stage is
activated. Comparing this to the SG3561A device, a 40% reduc-
tion in start-up current is achieved, resulting in 40% less power
dissipation in the start-up resistor. This is especially important
in electronic ballast applications that are designed to operate in
harsh environments, with convection cooling as the only means
of heat dissipation.
low start-up current of the LX1562 in conjunction with a boot-
strap winding off of the power transformer. Circuit operation
is as follows:
resistor (R1) minus the start-up current drawn by the IC. This
resistor is typically chosen to provide 2X the maximum start-up
current at low line to guarantee start-up under the worst case
condition. Once the capacitor voltage reaches the start-up
threshold, the IC turns on, starting the switching cycle. The
operation of the IC demands an increase in operating current
which results in discharging the capacitor. During the discharge
cycle, the flyback voltage of the auxiliary winding is rectified
and filtered via rectifier (D1) and charges the capacitor above
the minimum operating voltage of the device and takes over as
the supply voltage. The start-up capacitor and auxiliary wind-
ing must be selected such that it satisfies worst case IC condi-
tions. Figure 25 shows start-up time and voltage of capacitor C1.
The energy stored during switch on-time is now transferred
Figure 24 shows an efficient supply voltage using the ultra
The start-up capacitor (C1) is charged by current through
8/30
FIGURE 23 — INDUCTOR CURRENT
P R O D U C T D A T A B O O K 1 9 9 6 / 1 9 9 7
Inductor Peak
Current Envelope
S
Average
AC Input Current
E C O N D
P
-G
R O D U C T I O N
F U N C T I O N A L D E S C R I P T I O N
E N E R AT I O N
T
ON
I C D E S C R I P T I O N
I
L
T
OFF
P
O W E R
D
to ramp down. When current reaches zero level (inductor runs
out of energy) , boost diode (D1) stops conducting and the
residual inductor energy and the drain to source capacitance of
the power MOSFET create an LC tank circuit which causes drain
voltage to resonate at this frequency. The resonating voltage is
detected by the secondary winding (Idet winding) of the in-
ductor. When this voltage swings negative “I detect” pin senses
it and activates the blanking circuit , sets the latch, and turns
power MOSFET on, repeating the cycle. This operation contin-
ues for the entire cycle of the AC rectified input resulting in an
inductor current as shown in Figure 23. The high frequency
content of this current is then filtered by the input capacitor
(C1) resulting in a sine wave input current in phase with the
AC line voltage.
amplifier compares this voltage to an internal 2.5V reference
and generates an error voltage. This voltage then controls the
amplitude of the multiplier output adjusting the peak inductor
current proportional to the load and line variations, maintain-
ing a well regulated voltage.
and LX1563. The LX1562 is used for stand alone pre-regulator
applications while LX1563 is ideal for applications where sup-
ply voltage is derived elsewhere and requires less than 14V
start-up.
A T A
F
Output voltage regulation is accomplished when the error
Table 1 shows the start-up voltage and hysteresis for LX1562
A C T O R
Rectified
AC Line
FIGURE 24 — TYPICAL APPLICATION OF START-UP CIRCUITRY
GND
S
C
C1
H E E T
R1
O N T R O L L E R
LX1562
LX1563
Part #
I
1
> 300µA
T
Start-Up
I
Voltage
ST
A B L E
13.1V
9.8V
< 300µA
LX1562/1563
LX1562
1
GND
V
IN
Hysteresis
Voltage
V
5.2V
2.1V
O
D1
R
S
13