at90ls8535-8mi ATMEL Corporation, at90ls8535-8mi Datasheet - Page 105

• Manufacturer Part Number: at90ls8535-8mi
• Description: 8-bit Microcontroller With 8k Bytes In-system Programmable Flash
• Manufacturer: ATMEL Corporation

DC Characteristics (Continued)
T
Notes:
1041H–11/01
A
Symbol
= -40 ° C to 85 ° C, V
V
t
I
ACPD
ACLK
ACIO
1. “Max” means the highest value where the pin is guaranteed to be read as low (logical “0”).
2. “Min” means the lowest value where the pin is guaranteed to be read as high (logical “1”).
3. Although each I/O port can sink more than the test conditions (20 mA at V
4. Although each I/O port can source more than the test conditions (3 mA at V
5. Minimum V
conditions (non-transient), the following must be observed:
PDIP Package:
1] The sum of all I
2] The sum of all I
3] The sum of all I
PLCC and TQFP Packages:
1] The sum of all I
2] The sum of all I
3] The sum of all I
4] The sum of all I
5] The sum of all I
6] The sum of all I
7] The sum of all I
8] The sum of all I
If I
than the listed test condition.
conditions (non-transient), the following must be observed:
PDIP Package:
1] The sum of all I
2] The sum of all I
3] The sum of all I
PLCC and TQFP Packages:
1] The sum of all I
2] The sum of all I
3] The sum of all I
4] The sum of all I
5] The sum of all I
6] The sum of all I
7] The sum of all I
8] The sum of all I
If I
greater than the listed test condition.
Parameter
Analog Comparator Input
Offset Voltage
Analog Comparator Input
Leakage A
Analog Comparator
Propagation Delay
OL
OH
exceeds the test condition, V
exceeds the test condition, V
CC
CC
for power-down is 2V.
= 2.7V to 6.0V (unless otherwise noted)
OL
OL
OL
OL
OL
OL
OL
OL
OL
OL
OL
OH
OH
OH
OH
OH
OH
OH
OH
OH
OH
OH
, for all ports, should not exceed 200 mA.
, for port A0 - A7, should not exceed 100 mA.
, for ports B0 - B7, C0 - C7, D0 - D7 and XTAL2, should not exceed 100 mA.
, for all ports, should not exceed 400 mA.
, for ports A0 - A7, should not exceed 100 mA.
, for ports B0 - B3, should not exceed 100 mA.
, for ports B4 - B7, should not exceed 100 mA.
, for ports C0 - C3, should not exceed 100 mA.
, for ports C4 - C7, should not exceed 100 mA.
, for ports D0 - D3 and XTAL2, should not exceed 100 mA.
, for ports D4 - D7, should not exceed 100 mA.
, for all ports, should not exceed 200 mA.
, for port A0 - A7, should not exceed 100 mA.
, for ports B0 - B7, C0 - C7, D0 - D7 and XTAL2, should not exceed 100 mA.
, for all ports, should not exceed 400 mA.
, for ports A0 - A7, should not exceed 100 mA.
, for ports B0 - B3, should not exceed 100 mA.
, for ports B4 - B7, should not exceed 100 mA.
, for ports C0 - C3, should not exceed 100 mA.
, for ports C4 - C7, should not exceed 100 mA.
, for ports D0 - D3 and XTAL2, should not exceed 100 mA.
, for ports D4 - D7, should not exceed 100 mA.
Condition
V
V
V
V
V
V
CC
in
CC
in
CC
CC
OL
= V
= V
= 5V
= 5V
= 2.7V
= 4.0V
OH
may exceed the related specification. Pins are not guaranteed to sink current greater
CC
CC
may exceed the related specification. Pins are not guaranteed to source current
/2
/2
-50.0
Min
CC
CC
= 5V, 10 mA at V
= 5V, 1.5 mA at V
750.0
500.0
Typ
AT90S/LS8535
CC
CC
= 3V) under steady state
Max
40.0
50.0
= 3V) under steady state
Units
mV
nA
ns
105