cop8cce9imt9 National Semiconductor Corporation, cop8cce9imt9 Datasheet - Page 23
cop8cce9imt9
Manufacturer Part Number
cop8cce9imt9
Description
8-bit Cmos Flash Microcontroller With 8k Memory, Virtual Eeprom, 10-bit A/d And Brownout Reset
Manufacturer
National Semiconductor Corporation
Datasheet
1.COP8CCE9IMT9.pdf
(80 pages)
- Current page: 23 of 80
- Download datasheet (962Kb)
10.0 Functional Description
10.7.1 External Reset
The RESET input, when pulled low, initializes the device.
The RESET pin must be held low for a minimum of one
instruction cycle to guarantee a valid reset.
RESET may also be used to cause an exit from the HALT
mode.
A recommended reset circuit for this device is shown in
Figure 9.
(Continued)
WATCHDOG (if enabled):
The device comes out of reset with both the WATCHDOG
logic and the Clock Monitor detector armed, with the
WATCHDOG service window bits set and the Clock Moni-
tor bit set. The WATCHDOG and Clock Monitor circuits
are inhibited during reset. The WATCHDOG service win-
dow bits, being initialized high, default to the maximum
WATCHDOG service window of 64k T0 clock cycles. The
Clock Monitor bit being initialized high will cause a Clock
Monitor error following reset if the clock has not reached
the minimum specified frequency at the termination of
reset. A Clock Monitor error will cause an active low error
output on pin G1. This error output will continue until
16–32 T0 clock cycles following the clock frequency
reaching the minimum specified value, at which time the
G1 output will go high.
FIGURE 9. Reset Circuit Using External Reset
20022512
23
10.7.2 On-Chip Brownout Reset
When enabled, the device generates an internal reset as
V
voltage (V
the Idle Timer is preset with 00Fx (240–256 t
reaches a value greater than V
counting down. Upon underflow of the Idle Timer, the internal
reset is released and the device will start executing instruc-
tions. This internal reset will perform the same functions as
external reset. Once V
Timer time-out takes place, instruction execution begins and
the Idle Timer can be used normally. If, however, V
below the selected V
the Idle Timer is preset with 00Fx. The device now waits until
V
functional operation of the device, at frequency, is guaran-
teed down to the V
CC
CC
is greater than V
rises. While V
bor
), the device is held in the reset condition and
bor
CC
bor
bor
CC
level.
is less than the specified brownout
, an internal reset is generated, and
and the countdown starts over. The
is above the V
bor
, the Idle Timer starts
bor
and this initial Idle
C
). When V
www.national.com
CC
drops
CC
Related parts for cop8cce9imt9
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
IC C-COMPLIER SOFTWARE FOR COP8
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Freescale Semiconductor Technical Data
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Self-calibrating 12-bit Plus Sign Serial I/o A/d Converters With Mux And Sample/hold
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Pllatinum Tm Fractional N Rf / Integer N If Dual Low Power Frequency Synthesizer
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Pllatinum? 2.0 Ghz Frequency Synthesizer For Rf Personal Communications
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Pllatinumtm 160 Mhz Frequency Synthesizer For Rf Personal Communications
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Dual N-channel Enhancement Mode Field Effect Transistor
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Video Amplifier System (obsolete)
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Synchronous Step-up DC/DC Converter For White Led Applications
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
CLC420 - High Speed, Voltage Feedback op Amp, Package: Lcc, Pin Nb=20
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Monolithic Triple 4.5 CRT Driver
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Differential Video Amplifier
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
ADC10061 - 10-Bit 600 NS A/D Converter With Input Multiplexer And Sample/Hold, Package: Soic Wide, Pin Nb=20
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
DS36277 - Dominant Mode Multipoint Transceiver, Package: Soic Narrow, Pin Nb=8
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Printer Solenoid Driver
Manufacturer:
National Semiconductor Corporation
Datasheet: