acpl-h312 Avago Technologies, acpl-h312 Datasheet
acpl-h312
Available stocks
Related parts for acpl-h312
acpl-h312 Summary of contents
Page 1
... IGBTs with ratings up to 1200 V/100 A. For IGBTs with higher ratings, the ACPL-H312 /K312 series can be used to drive a discrete power stage which drives the IGBT gate. The ACPL-H312 has an insulation voltage 891 V (Option 060). The ACPL-K312 has an is- ...
Page 2
... To order, choose a part number from the part number column and combine with the desired option from the option column to form an order entry. Example 1: ACPL-H312-560E to order product of Stretched SO8 Surface Mount package in Tape and Reel packaging with IEC/EN/ DIN EN 60747-5-2 Safety Approval in RoHS compliant. Example 2: ACPL-H312-000E to order product of Stretched SO8 Surface Mount package in Tube Packaging and RoHS compliant ...
Page 3
... ACPL-K312 Outline Drawing - Stretched S08 0.381±0.13 .015±.005 0.450 7˚ .018 45˚ 0.200±0.100 .008±.004 0.750±0.250 0.0295±0.010 11.5±0.250 .453±.010 Recommended Solder Reflow Temperature Profile 300 PREHE ATING RATE 3°C + 1°C/–0.5°C/SEC. ...
Page 4
... T =150°C smax smin Non-halide flux should be used Regulatory Information The ACPL-H312/K312 is pending approval by the following organizations: IEC/EN/DIN EN 60747-5-2 (ACPL-H312/K312 Option 060 only) Approval under: IEC 60747-5-2 :1997 + A1:2002 EN 60747-5-2:2001 + A1:2002 DIN EN 60747-5-2 (VDE 0884 Teil 2):2003-01 UL Approval under UL 1577, component recognition program, File E55361 ...
Page 5
... There are recommended techniques such as grooves and ribs which may be used on a printed circuit board to achieve desired creepage and clearances. Creepage and clearance distances will also change depending on factors such as pollution degree and insulation level. 5 (ACPL-H312/K312 Option 060) [1] Symbol V ...
Page 6
Table 3. Absolute Maximum Ratings Parameter Symbol Storage Temperature T Operating Temperature T A Junction Temperature T Average Input Current I F(AVG) Peak Transient Input Current I F(TRAN) (<1 µs pulse width, 300pps) Reverse Input Voltage V “High” Peak Output ...
Page 7
Table 5. Electrical Specifications (DC) Over recommended operating conditions ( Ground) unless otherwise specified. All typical values Parameter Symbol High Level Output Current I OH Low Level Output Current I OL High Level Output Voltage ...
Page 8
Table 6. Switching Specifications (AC) Over recommended operating conditions ( Ground) unless otherwise specified. All typical values Parameter Propagation Delay Time to High Output Level Propagation Delay Time to Low Output Level Pulse Width Distortion ...
Page 9
... This load condition approximates the gate load of a 1200 V/100A IGBT. 9. Pulse Width Distortion (PWD) is defined as |t 10. The difference between tPHL and t between any two ACPL-H312/K312 parts under the same test condition. PLH 11. Pins 3 and 4 need to be connected to LED common. 12. Common mode transient immunity in the high state is the maximum tolerable dV will remain in the high state (i.e., V > ...
Page 10
-100 mA OUT -40 - – TEMPERATURE – °C A ...
Page 11
T -TEMPERATURE-ºC A Figure 7. I vs. Temperature 30V VEE =0V 4 OUTPUT=OPEN -40 - ...
Page 12
I F =7mA 30V,VEE= =10nF 400 DUTY CYCLE=50% f=10kHz 300 200 100 -SERIES LOAD RESISTANCE-Ω g Figure 13. Propagation Delay vs ...
Page 13
16mA Figure 17. I test circuit 16mA Figure 19. V test circuit OH ...
Page 14
16mA F 500Ω 10kHz, 50% Duty Cycle 3 4 Figure 23 test circuit and waveforms PLH PHL ...
Page 15
... Typical Application Circuit Figure 25 and 26 show two gate driver application circuit using ACPL-H312/K312. AN5336 application note describes general method on gate drive optocoupler design 270Ω Figure 25. Recommended LED drive and application circuit 270Ω ...
Page 16
... Thermal Model for ACPL-H312/K312 Streched-SO8 Package Optocoupler Definitions R : Junction to Ambient Thermal Resistance of LED due 11 to heating of LED R : Junction to Ambient Thermal Resistance of LED due 12 to heating of Detector (Output IC Junction to Ambient Thermal Resistance of Detector 21 (Output IC) due to heating of LED Junction to Ambient Thermal Resistance of Detector 22 (Output IC) due to heating of Detector (Output IC) ...
Page 17
... Quick Gate Drive Design Example using ACPL-H312/K312 The total power dissipation (PT) is equal to the sum of the LED input-side power (PI) and detector output-side power (PO) dissipation F(ON) ,max F,max where 16mA (Table 4) F(ON),max V = 1.8V (Table 5) F,max PO = PO(BIAS) + PO(SWTICH CC2 SWITCH where, PO(BIAS) = steady-state power dissipation in the driver due to biasing the device ...