op4005b1 RF Monolithics, Inc., op4005b1 Datasheet
![no-image](/images/no-image-200.jpg)
op4005b1
Manufacturer Part Number
op4005b1
Description
622.08 Mhz Optical Timing Clock
Manufacturer
RF Monolithics, Inc.
Datasheet
1.OP4005B1.pdf
(2 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
OP4005B1
Manufacturer:
RFM
Quantity:
5 000
• Quartz SAW Stabilized Differential Output Technology
• Very Low Jitter Fundamental-Mode Operation at 622.08 MHz
• Voltage Tunable for Phase Locked Loop Applications
• Timing Reference for Optical Data Communications Systems
The OP4005B1 is a voltage-controlled SAW clock (VCSC) designed for phase-locked loop (PLL) applications
in optical data communications systems. The differential outputs of the OP4005B1 are generated by high-Q,
fundamental mode quartz surface acoustic wave (SAW) technology. This technique provides very low output
jitter and phase noise, plus excellent immunity to power supply noise. The OP4005B1 differential outputs
feature ±1% symmetry, and can be DC-configured to drive a wide range of high-speed logic families. The
OP4005B1 is packaged in a hermetic metal-ceramic LCC.
Absolute Maximum Ratings
1.
2.
3.
4.
5.
6.
7.
8.
www.RFM.com
©2008 by RF Monolithics, Inc.
Electrical Characteristics
Rating
DC Suppy Voltage
Tune Voltage
Case Temperature
Characteristic
Input Impedence (Tuning Port)
Output DC Resistance (between Q & Q)
DC Power Supply
Operating Frequency
Q and Q Output
Phase Noise
Q and Q Jitter
Operating Case Temperature
Lid Symbolization (YY=Year, WW=Week)
Unless otherwise noted, all specifications include the combined effects of load VSWR, V
Net tuning range after tuning out the effects of initial manufacturing tolerances, VSWR pushing/pulling, V
The internal design, manufacturing processes, and specifications of this device are subject to change without notice.
Specified only for a balanced load with a VSWR < 1.2 ( 50 ohms each side), and a V
Symmetry is defined as the width in (% of total period) measure at 50% of the peak-to-peak voltage of either output.
Jitter and other noise outputs due to power supply noise or mechanical vibration are not included in this specification except where noted.
Applies to period jitter of either differential output. Measured with a Tektronix CSA803 signal analyzer with at least 1000 samples.
One or more of the following United States patents apply: 4, 616,197; 4,670,681; 4,760,352.
CAUTION: Electrostatic Sensitive Device. Observe precautions for handling. COCOM CAUTION: Approval by the U.S.
Department of Commerce is required prior to export of this device.
Notes:
E-mail: info@rfm.com
Voltage into 50 Ω (VSWR ≤ 1.2)
Absolute Frequency
Tuning Range
Tuning Voltage
Tuning Linearity
Modulation Bandwidth
Operating Load VSWR
Symmetry
Harmonic Spurious
Nonharmonic Spurious
@ 100 Hz offset
@ 1 kHz offset
@ 10 kHz offset
Noise Floor
RMS Jitter (10kHz to 80MHz)
No Noise on V
200 mV
Operating Voltage
Operating Current
P-P
Noise, from 1 MHz to ½ f
CC
O
on V
CC
Sym
V
I
V
-55 to 100
T
f
CC
CC
O
0 to 5.5
0 to 5.5
O
C
Value
3, 4, 6, 7
3, 4, 6, 7
3, 4, 6, 7
Notes
3, 4, 5
3, 4, 6
3, 6
3, 6
3, 6
3, 6
1, 3
1, 3
1, 3
1, 3
1,3
1,3
1
2
1
1
3
CC
= 3.0 Vdc.
CC
Units
and T
Vdc
Vdc
°C
RFM OP4005B1 YYWW
Minimum
-40°C
0.60
3.13
200
C
45
50
.
0
8
CC
, T
3.3 or 5.0
Typical
C
622.08
±100
-100
-125
-150
Timing Clock
-70
0.1
and aging.
±5
12
12
10
622.08 MHz
OP4005B1
Optical
Maximum
SMC-08A
+85°C
5.25
-15
-60
3.3
1.1
2:1
55
70
OP4005B1 - 3/27/08
Page 1 of 2
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
Units
ps
ps
MHz
ppm
V
Vdc
kHz
dBc
dBc
Vdc
mA
KΩ
KΩ
ps
°C
%
%
P-P
P-P
P-P
Related parts for op4005b1
op4005b1 Summary of contents
Page 1
... This technique provides very low output jitter and phase noise, plus excellent immunity to power supply noise. The OP4005B1 differential outputs feature ±1% symmetry, and can be DC-configured to drive a wide range of high-speed logic families. The OP4005B1 is packaged in a hermetic metal-ceramic LCC ...
Page 2
... Typically 0.01" to 0.05" Places) (The optimum value of this dimension is dependent on the PCB assembly process employed.) mm Inches MIN MAX MIN A 13.46 13.97 0.530 B 9.14 9.66 0.360 C 1.93 Nominal 0.076 Nominal D 1.93 Nominal 0.076 Nominal E 2.54 Nominal 0.100 Nominal F 1.27 Nominal 0.050 Nominal D F MAX 0.550 0.380 Page OP4005B1 - 3/27/08 ...