lp3205 Lowpower Semiconductor inc, lp3205 Datasheet - Page 7
![no-image](/images/no-image-200.jpg)
lp3205
Manufacturer Part Number
lp3205
Description
1.5mhz,800ma,high Efficiency Synchronous Pwm Step-down Dc/dc Convert
Manufacturer
Lowpower Semiconductor inc
Datasheet
1.LP3205.pdf
(10 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
lp3205-12B5F
Manufacturer:
POWER
Quantity:
20 000
Part Number:
lp3205-18B5F
Manufacturer:
LOWPOWER
Quantity:
20 000
Part Number:
lp3205-33B5F
Manufacturer:
POWER
Quantity:
20 000
Part Number:
lp3205-AB5F
Manufacturer:
POWER
Quantity:
20 000
Part Number:
lp3205FAB5F
Manufacturer:
LOWPOWER
Quantity:
20 000
Applications Information
The basic LP3205 application circuit is shown in Typical
Application Circuit. External component selection is
determined by the maximum load current and begins with
the selection of the inductor value and operating
frequency followed by CIN and COUT.
Inductor selection
The output inductor is selected to limit the ripple
current to some predetermined value. typically 20%~40%
of the full load current at the maximum input voltage.
Large value inductors lower ripple currents. Higher Vin or
V
equation. A reasonable starting point for setting ripple
current is △I
The DC current rating of the inductor should be at least
equal to the maximum load current plus half the ripple
current to prevent core saturation. Thus, a 720mA rated
Inductor should be enough for most applications
(800mA+120mA). For better efficiency, choose a low
DC-resistance inductor.
C
The input capacitance, C
trapezoidal current at the source of the top MOSFET. To
prevent large ripple voltage, a low ESR input capacitor
Sized for the maximum RMS current should be used.
RMS current is given by:
Th
I
commonly.Used for design because even significant
deviations do not offer much relief. Note that ripple
current ratings from capacitor manufacturers are often
based on only 2000 hours of life which makes it advisable
to further derate the Capacitor, or choose a capacitor
rated at a higher temperature Than required. Several
capacitors may also be paralleled to meet size or height
requirements in the design.
The selection of C
LP3205 – Ver. 1.0 Datasheet
RMS
OUT
IN
is formula has a maximum at V
and C
=I
also increases the ripple current as shown in
OUT
/2.this
OUT
L
Selection
=240mA(40% of 800mA).
OUT
simple
is determined by the effective
IN
worst-case
Feb.-2007
,is needed to filter the
Preliminary Datasheet
IN
=2V
condition
OUT
, where
is
series resistance(ESR) that is required to minimize
voltage ripple and load step transients, an well as the
amount or bulk capacitance that is necessary to ensure
that the control loop is stable. Loop stability can be
checked by vie sing the load transient response as
described in later section. the output ripple,△V
determined by:
Using ceramic input and output capacitors
Higher values, lower cost ceramic capacitors are now
becoming .Available in smaller case sizes ,their high
ripple current ,high voltage rating and low ESR make
them ideal for switching regulator applications. however
care must be taken when these capacitors are used at the
input and output. When a ceramic capacitor is use at
input and the power is supplied by a wall adapter through
long wires, a load step at the output can induce ringing at
the input ,V
through the long wires can potentially cause a voltage
spike at V
Output voltage programming
The output voltage is set by a resistive divider according
to the
Following formula:
The external resistive divider is connected to the output,
allowing Remote voltage sensing as shown in figure3.
Efficiency considerations
The efficiency of a switching regulator is equal to the output
Power divided by the input power times 100%.it is often useful
to analyze individual losses to determine what is limiting the
efficiency and which change would produce the most
improvement efficiency can be expressed as :
IN
large enough to damage the part.
IN
, At worst, a sudden inrush of current
Page 7 of 10
LP3205
OUT
, is