lp3855et-3.3 National Semiconductor Corporation, lp3855et-3.3 Datasheet - Page 8
![no-image](/images/no-image-200.jpg)
lp3855et-3.3
Manufacturer Part Number
lp3855et-3.3
Description
1.5a Fast Response Ultra Low Dropout Linear Regulators
Manufacturer
National Semiconductor Corporation
Datasheet
1.LP3855ET-3.3.pdf
(19 pages)
www.national.com
Electrical Characteristics
LP3852/LP3855
Shutdown Input
Error Flag
AC Parameters
Note 1: Absolute maximum ratings indicate limits beyond which damage to the device may occur. Operating ratings indicate conditions for which the device is
intended to be functional, but does not guarantee specific performance limits. For guaranteed specifications and test conditions, see Electrical Characteristics. The
guaranteed specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed
test conditions.
Note 2: At elevated temperatures, devices must be derated based on package thermal resistance. The devices in TO220 package must be derated at θ
(with 0.5in
0.5in
Note 3: The human body model is a 100pF capacitor discharged through a 1.5kΩ resistor into each pin.
Note 4: Typical numbers are at 25˚C and represent the most likely parametric norm.
Note 5: Limits are guaranteed by testing, design, or statistical correlation.
Note 6: If used in a dual-supply system where the regulator load is returned to a negative supply, the output must be diode-clamped to ground.
Note 7: The output PMOS structure contains a diode between the V
if the voltage at the output terminal is forced to be higher than the voltage at the input terminal. This diode can typically withstand 200mA of DC current and 1Amp
of peak current.
Note 8: Output voltage line regulation is defined as the change in output voltage from the nominal value due to change in the input line voltage. Output voltage load
regulation is defined as the change in output voltage from the nominal value due to change in load current. The line and load regulation specification contains only
the typical number. However, the limits for line and load regulation are included in the output voltage tolerance specification.
Note 9: Error Flag threshold and hysteresis are specified as percentage of regulated output voltage. See Application Hints.
Note 10: Dropout voltage is defined as the minimum input to output differential voltage at which the output drops 2% below the nominal value. Dropout voltage
specification applies only to output voltages of 2.5V and above. For output voltages below 2.5V, the drop-out voltage is nothing but the input to output differential,
since the minimum input voltage is 2.5V.
Note 11: The minimum operating value for V
Note 12: The SOT 223 package devices have slightly higher dropout due to increased bond wire resistance.
Limits in standard typeface are for T
Unless otherwise specified: V
Symbol
V
PSRR
T
V
T
ρ
EF(Sat)
V
I
2
dOFF
I
V
Td
max
dON
n(l/f)
e
SDT
SD
I
, 1oz. copper area), junction-to-ambient. See Application Hints.
TH
lk
T
n
2
, 1oz. copper area), junction-to-ambient (with no heat sink). The devices in the TO263 surface-mount package must be derated at θ
Shutdown Threshold
Turn-off delay
Turn-on delay
SD Input Current
Threshold
Threshold Hysteresis
Error Flag Saturation
Flag Reset Delay
Error Flag Pin Leakage
Current
Error Flag Pin Sink
Current
Ripple Rejection
Output Noise Density
Output Noise Voltage
Parameter
(Continued)
IN
= V
IN
O(NOM)
J
is equal to either [V
= 25˚C, and limits in boldface type apply over the full operating temperature range.
+ 1V, I
Output = High
Output = Low
I
I
V
(Note 9)
(Note 9)
I
V
V
C
V
V
C
V
f = 120Hz
BW = 10Hz – 100kHz
V
BW = 300Hz – 300kHz
V
L
L
sink
SD
Error
IN
OUT
IN
OUT
OUT
OUT
OUT
OUT
= 1.5A
= 1.5A
= V
= V
L
= 100µA
= V
= 10 mA, C
= 3.3V, f = 120Hz
= 3.3V, f = 120Hz
= 2.5V
= 2.5V
= 0.5V
= 10uF
= 10uF
IN
OUT(NOM)
OUT
OUT
IN
Conditions
and V
+ 1V
+ 0.5V
OUT
+ V
8
terminals. This diode is normally reverse biased. This diode will get forward biased
DROPOUT
OUT
= 10µF, V
] or 2.5V, whichever is greater.
SD
(Note
0.02
= 2V.
Typ
150
100
V
0.8
20
25
10
73
57
4)
0
1
5
1
1
1
IN
LP3852/5 (Note 5)
Min
2
5
2
Max
0.3
0.1
16
8
jA
= 60˚C/W (with
jA
µV (rms)
= 50˚C/W
Units
mA
nA
nA
dB
µV
µs
µs
µs
%
%
V
V