pex8111 ETC-unknow, pex8111 Datasheet
pex8111
Manufacturer Part Number
pex8111
Description
Pci Express To Pci Bridge
Manufacturer
ETC-unknow
Datasheet
1.PEX8111.pdf
(2 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
pex8111-AA66BES
Manufacturer:
PLX
Quantity:
20 000
Company:
Part Number:
pex8111-BB66BC
Manufacturer:
HITTITE
Quantity:
1 400
Company:
Part Number:
pex8111-BB66BC
Manufacturer:
PLX
Quantity:
648
Company:
Part Number:
pex8111-BB66BCF
Manufacturer:
PLX
Quantity:
1 400
Company:
Part Number:
pex8111-BB66BCF
Manufacturer:
PLX
Quantity:
586
Part Number:
pex8111-BB66BES F
Manufacturer:
PLXTECH
Quantity:
20 000
Company:
Part Number:
pex8111-BB66FBC
Manufacturer:
PLX
Quantity:
1 400
Features
S
S
S
.
General Features
Integrated PCI Express Interface
PCI Interface
o Forward and Reverse bridging
o
o
o
o
o 1.5 V core supply voltage
o JTAG
o Four (4) GPIO pins for maximum
o Extensive PME support including
o PCI Express Base specification 1.0a
o x1 Link, full-duplex, 2.5 Gbps
o One virtual channel
o Automatic LVDS polarity reversal
o 128 byte maximum payload size
o Link CRC
o Link power management
o Flow control buffering
o PCI Express transaction queues for
o PCI 3.0: 32 bits at 33 MHz
o PCI Power Management 1.1
o Internal arbiter supports up to 4
o 3.3V I/O and 5V tolerant PCI
o Message Signal Interrupt (MSI)
o Provides PCI clock output
o Four mailbox registers for messaging
o
Tiny 161 ball BGA package
(10mm x 10mm)
Low power – 0.3 Watts maximum
EEPROM configuration option with
SPI
Internal 8Kbyte shared RAM
design and application flexibility
D0 and D0
and D3
compliant
eight (8) outstanding TLPs
external masters; provides
REQ#/GNT# signals
support
ISA Enable and VGA Enable
registers for legacy operation
Version 1.0 2004
Cold
Active
, D1, D2 and D3
x x x x x x x x x
Hot
Reversible Bridge in a Tiny Package
The PLX Technology PEX 8111 bridge enables designers to migrate legacy PCI bus
interfaces to the new advanced serial PCI Express. This is ideal when including
existing PCI ICs on a PCI Express™ Adapter Board, such as the new ExpressCard™
standard. This simple bridge can also reside on either end of a PCI Express cable to
connect remote functions running the PCI protocol. The PEX 8111 supports
forward and reverse bridging. The tiny 10 mm x 10mm Plastic BGA package
makes the PEX 8111 bridge ideal for use in applications where board real estate is at
a premium. With its low power 0.15 micron CMOS design, the PEX 8111 consumes
a maximum power of only 300 mW.
Forward and Reverse Bridging
Compliant to the PCI Express-to-PCI/PCI-X Bridge Specification 1.0, the PEX 8111
is capable of operating in either forward or reverse bridging modes. In forward
mode, the bridge allows legacy PCI chips and adapters to be used with new PCI
Express processor systems. Reverse bridge operation allows conventional PCI
processors and chipsets to configure and control advanced PCI Express switches and
endpoints. The reverse PEX 8111 not only allows complete configuration of a
downstream PCI Express system from the PCI bus, but it also handles limited
PCI Express root functions for reverse interrupt and Power Management Events.
Block Diagram
The PEX 8111 is equipped with a
standard PCI Express port that operates
as a single, x1 link with a maximum of
250 Megabytes per second of throughput
per transmit and receive direction. With a
single 2.5 Gbps integrated SerDes, the
standard PCI Express signaling delivers
the highest bandwidth with the lowest
possible pin count using LVDS
technology.
The PEX 8111 has a single parallel bus
segment supporting the PCI v 3.0
protocol. With a 32-bit wide parallel data
path running at 33MHz, the PCI
bandwidth is 132 Megabytes per second.
While the PCI Express link
accommodates the full PCI bus
bandwidth, the device also supports
internal queues with flow control features
to optimize throughput and traffic flow.
PCI Express to PCI Bridge
PEX 8111
Figure 1. PEX 8111 Block Diagram
PCI Express Link (1 lane, 1 Virtual Channel, 2.5 GHz)
Configuration
PCI Master and Target Interface Logic
Registers
PCI Express Transaction Layer
PCI Express Data Link Layer
(Packet Construction Logic)
PCI Express PHY Layer
PCI Bus (32 Bit, 33 MHz)
FIFOs
j
8K Shared
RAM
Related parts for pex8111
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Manufacturer:
ETC-unknow
Datasheet:
Part Number:
Description:
Manufacturer:
ETC-unknow
Datasheet:
pex8111 Summary of contents
Page 1
Version 1.0 2004 . Features S General Features o Forward and Reverse bridging o Tiny 161 ball BGA package (10mm x 10mm) o Low power – 0.3 Watts maximum o EEPROM ...
Page 2
Design Applications ExpressCard™ Adapter – Forward Bridge The PEX 8111 can be used to quickly upgrade legacy PCI adapter board designs to be compatible with PCI Express standard interface slots. In Figure 2, an existing CardBus™ converted for ...