afct-57m5atp ETC-unknow, afct-57m5atp Datasheet
afct-57m5atp
Related parts for afct-57m5atp
afct-57m5atp Summary of contents
Page 1
... Description The AFCT-57M5ATP is a state of the art transceiver designed to provide a cost effective, high performance solution for 2.125 GBd and 1.0625 GBd Fibre Channel and 1.25 GBd Ethernet enhancement to the conventional SFP interface defined in SFF-8074i, the AFCT-57M5ATP is compliant to SFF-8472 (digital diagnostic interface for SFP). Using the ...
Page 2
... Installation The AFCT-57M5ATP can be installed in any SFF-8074i compliant Small Form Pluggable (SFP) port regardless of host equipment operating status. The AFCT-57M5ATP is hot- pluggable, allowing the module to be installed while the host system is operating and on- line. Upon insertion, the transceiver housing makes initial contact with the host ...
Page 3
... It may also result in improper operation of the AFCT-57M5ATP circuitry, and possible overstress of the laser source. Device degradation or product failure may result. Connection of the AFCT-57M5ATP to a non- approved optical source, operating above the recommended absolute maximum conditions may be considered an act of modifying or manufacturing a laser product ...
Page 4
... MHz to 1 GHz w/o chassis enclosure CDRH certification # TBD TUV file # TBD UL File # E173874 Electromagnetic Interference (EMI) Most equipment designs using the AFCT-57M5ATP are subject to the requirements of the FCC in the United States, CENELEC EN55022 (CISPR 22) in Europe and VCCI in Japan. The metal housing and shielded design of ...
Page 5
V Tx_FAULT VREFR VREFR TX[0:9] TBC TBC EWRAP EWRAP PROTOCOL IC RX[0:9] RBC RBC Rx_RATE Rx_RATE REFCLK Rx_LOS GPIO(X) GPIO(X) GP14 REFCLK 106.25 MHz Figure 2. Typical Application Configuration 0.1 µ 0.1 µF ...
Page 6
Table 2. Pin Description Pin Name TX_FAULT 3 TX_DISABLE 4 MOD-DEF2 5 MOD-DEF1 6 MOD-DEF0 7 8 RX_LOS RD- 13 RD+ 14 ...
Page 7
Absolute Maximum Ratings Parameter Case Operating Temperature Relative Humidity Module Supply Voltage Data/Control Input Voltage Recommended Operating Conditions Parameter Case Operating Temperature Module Supply Voltage Data Rate Transceiver Electrical Characteristics Parameter Ac Electrical Characteristics Power Supply Noise Rejection (peak-to-peak) Dc ...
Page 8
Transmitter and Receiver Electrical Characteristics (T = -10 °C to +85 ° 3.3 V ± 10 Parameter Data Input: Transmitter Differential Input Voltage (TD+/-) Data Output: Receiver Differential Output Voltage (RD+/-) Contributed ...
Page 9
Transmitter Optical Characteristics (T = -10 °C to +85 ° 3.3 V ± 10 Parameter Modulated Optical Output Power (OMA) (Peak-to-Peak) 2.125 Gb/s Modulated Optical Output Power (OMA) (Peak-to-Peak) 1.0625 Gb/s Modulated ...
Page 10
Receiver Optical Characteristics (T = -10 °C to +85 ° 3.3 V ± 10 Parameter Input Optical Power Input Optical Modulation Amplitude (Peak-to-Peak) 2.125 Gb/s Input Optical Modulation Amplitude (Peak-to-Peak) 1.0625 Gb/s ...
Page 11
Transceiver Timing Characteristics (T = -10 °C to +85 ° 3.3 V ± 10 Parameter Hardware TX_DISABLE Assert Time Hardware TX_DISABLE Negate Time Time to initialize, including reset of TX_FAULT Hardware TX_FAULT ...
Page 12
Transceiver Digital Diagnostic Monitor (Real Time Sense) Characteristics (T = -10 °C to +85 ° 3.3V ± 10 Parameter Transceiver Internal Temperature Accuracy Transceiver Internal Supply Voltage Accuracy Transmitter Laser DC Bias ...
Page 13
... Addresses 63 and 95 are checksums calculated (per SFF-8472 and SFF-8074) and stored prior to product shipment. 7. Addresses 68-83 specify the AFCT-57M5ATP ASCII serial number and will vary on a per unit basis. 8. Addresses 84-91 specify the AFCT-57M5ATP ASCII date code and will vary on a per date code basis. 13 ...
Page 14
Table 4. EEPROM Serial ID Memory Contents – Enhanced Feature Set Memory (Address A2h) Byte # Notes Decimal 0 Temp H Alarm MSB 1 1 Temp H Alarm LSB Temp L Alarm MSB 1 3 Temp L ...
Page 15
... Data Ready (Bar) Notes: 1. The response time for soft commands of the AFCT-57M5ATP is 100 msec as specified by the MSA SFF-8472 2. Bit 6 is logic OR’d with the SFP TX_DISABLE input pin 3; either asserted will disable the SFP transmitter. Table 6. EEPROM Serial ID Memory Contents – Alarms and Warnings (Address A2h, Bytes 112, 113, 116, 117) ...
Page 16
... Figure 5. Module drawing - dimensions are in millimeters [inches] 1.7 ± 0.9 3.5 ± 0.3 41.78 ± 0.5 15 MAX. 11.73 REF 9.8 MAX. PCB Figure 6. SFP Assembly Drawing AFCT-57M5TP Tcase REFERENCE POINT 15.25 ± 0.1 10 REF (to PCB) 16.25 ± 0.1 MIN. PITCH 0.4 ± 0.1 (below PCB) DIMENSIONS ARE IN MILLIMETERS CAGE ASSEMBLY 10.4 ± 0.1 ...
Page 17
Customer Manufacturing Processes This module is pluggable and is not designed for aqueous wash, IR reflow, or wave soldering processes. www.agilent.com/ semiconductors For product information and a complete list of distributors, please go to our web site. For technical assistance ...