ha2-5002-5 Intersil Corporation, ha2-5002-5 Datasheet
ha2-5002-5
Available stocks
Related parts for ha2-5002-5
ha2-5002-5 Summary of contents
Page 1
... For the military grade product, refer to the HA-5002/883 datasheet. Ordering Information PART NUMBER PART MARKING HA2-5002-2 HA2-5002-2 HA2-5002-5 HA2-5002-5 HA3-5002-5 HA3-5002-5 HA3-5002-5Z (Note) HA3-5002-5Z HA4P5002-5 HA4P5002-5 HA4P5002-5Z (Note) HA4P5002-5Z HA9P5002-5 ...
Page 2
Pinouts HA-5002 (PDIP, SOIC) TOP VIEW OUT HA-5002 HA-5002 (PLCC) TOP VIEW ...
Page 3
Absolute Maximum Ratings Voltage Between V+ and V- Terminals 44V Input Voltage . . . . . . . . . ...
Page 4
Electrical Specifications V SUPPLY PARAMETER Differential Gain R = 500Ω L Differential Phase R = 500Ω L POWER REQUIREMENTS Supply Current Power Supply Rejection Ratio A = 10V V NOTE: Slew Rate . 3. -------------------------- - ; V FPBW P ...
Page 5
Test Circuit and Waveforms OUT R = 50Ω 100Ω LARGE SIGNAL WAVEFORMS Schematic Diagram Application Information Layout Considerations The wide bandwidth ...
Page 6
It is also recommended that the bypass capacitors be connected close to the HA-5002 (preferably directly to the supply pins). Operation at Reduced Supply Levels The HA-5002 ...
Page 7
Typical Application +12V 50Ω 50Ω -12V Typical Performance Curves 9 = ±15V 50Ω GAIN 0 ...
Page 8
Typical Performance Curves 3 = ±15V -10 -11 -60 -40 - TEMPERATURE (°C) FIGURE 8. OFFSET VOLTAGE vs TEMPERATURE 15 = ±15V, R ...
Page 9
Typical Performance Curves 125° -55° SUPPLY VOLTAGE (±V) FIGURE 14. V MAXIMUM vs ...
Page 10
Metallization Mask Layout V + (ALT HA-5002 HA-5002 OUT V - (ALT FN2921.11 March 8, 2006 ...
Page 11
Dual-In-Line Plastic Packages (PDIP INDEX N/2 AREA -B- -A- D BASE PLANE -C- SEATING PLANE 0.010 (0.25 NOTES: 1. Controlling Dimensions: INCH. In case of conflict between ...
Page 12
Metal Can Packages (Can) REFERENCE PLANE Ø ØD ØD1 Øb1 Øb F BASE AND Q SEATING PLANE BASE METAL LEAD FINISH Øb1 Øb2 SECTION A-A NOTES: 1. (All leads) Øb applies between L1 ...
Page 13
Plastic Leaded Chip Carrier Packages (PLCC) 0.042 (1.07) 0.042 (1.07) 0.048 (1.22) 0.056 (1.42) PIN (1) IDENTIFIER 0.050 (1.27 0.020 (0.51) MAX 3 PLCS 0.026 (0.66) 0.032 (0.81) 0.045 (1.14) MIN VIEW “A” ...
Page 14
... Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use ...