hmc611 Hittite Microwave Corporation, hmc611 Datasheet
hmc611
Available stocks
Related parts for hmc611
hmc611 Summary of contents
Page 1
... LOGOUT pin is shorted to the VSET input, and will provide a nominal logarithmic slope of -25 mV/ dB and an intercept of 9 dBm (24 dBm for ƒ ≥ 5.8 GHz). The HMC611 can also be used in the controller mode where an external voltage is applied to the VSET pin, to create an AGC or APC feedback loop. ...
Page 2
... Operating Voltage Range Supply Current in Normal Mode Supply Current in Power Down Mode [1] Vcc= Vcc1= Vcc2= +5V [2] This parameter describes the open loop gain bandwidth of the HMC611 output amplifi er with no feedback from VSET to LOGOUT. Test Conditions Parameter Vcc1 = Vcc2 Input Ω Term Resistor at IN+ ...
Page 3
... Logout (+85c) Logout (-55c) 1 1 0.6 ERR (+25c) ERR (+85c) ERR (-55c) -3 0.2 -20 - Order On-line at www.hittite.com HMC611 60 dB, LOGARITHMIC Ideal Logout (+25C) Logout (+85C) Logout (-55C) 1 ERR (+25C) ERR (+85C) ERR (-55C) -70 -60 -50 -40 -30 -20 -10 0 INPUT POWER (dBm) Ideal ...
Page 4
... Logout (+25C) Logout (+85C) Logout (-55C) -4 -40 -30 -20 - INPUT POWER (dBm) LOGOUT Slope vs. Supply Voltage -25 -27 -29 -31 -33 4.5 10000 Order On-line at www.hittite.com HMC611 60 dB, LOGARITHMIC 3 Ideal Logout (+25C) 2 Logout (+85C) Logout (-55C ERR (+25C) ERR (+85C) ERR (-55C) -3 -30 -20 -10 0 ...
Page 5
... Unless otherwise noted: Vcc1, Vcc2 = +5V +25C [2] This data is relative to the room temperature performance of the HMC611 [3] Reference plane at input pad on test block Order On-line at www.hittite.com HMC611 60 dB, LOGARITHMIC 100 MHz 5800 MHz 1900 MHz 8000 MHz ...
Page 6
... TYPICAL BOND PAD IS 0.0024 SQUARE 4. BOND PAD METALIZATION: GOLD 5. BACKSIDE METALLIZATION: GOLD 6. BACKSIDE METAL IS GROUND 7. NO CONNECTION REQUIRED FOR UNLABELED BOND PADS 8. OVERALL DIE SIZE IS ±.002 Order On-line at www.hittite.com HMC611 60 dB, LOGARITHMIC Pad Size .0024 [0.100] x .0052 [0.193] .0024 [0.100] x .0024 [0.100 ...
Page 7
... Temperature sensor output pin Die bottom must be connected to RF and DC ground. Bias supply. Connect supply voltage to these pins with appropriate fi ltering. Temperature compensation pins. VSET input in controller mode. Short this pin to LOGOUT for detector mode. Order On-line at www.hittite.com HMC611 60 dB, LOGARITHMIC Interface Schematic ...
Page 8
... Applying voltage <0.2 x (Vcc1, Vcc2) will initiate power For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 DETECTOR / CONTROLLER 10000 MHz Description VSET for detector mode. saving mode. Order On-line at www.hittite.com HMC611 60 dB, LOGARITHMIC Interface Schematic ...
Page 9
... VSET should be connected to an external control voltage, typically be- tween +0.6 and +1.9V. Assembly Diagram For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 v01.0408 DETECTOR / CONTROLLER 10000 MHz Order On-line at www.hittite.com HMC611 60 dB, LOGARITHMIC ...
Page 10
... Thick GaAs MMIC 0.076mm 0.102mm (0.004”) Thick GaAs MMIC 0.076mm 0.150mm (0.005”) Thick Moly Tab Order On-line at www.hittite.com HMC611 60 dB, LOGARITHMIC Wire Bond (0.003”) RF Ground Plane 0.127mm (0.005”) Thick Alumina Thin Film Substrate Figure 1. ...