lc01707plf Sanyo Semiconductor Corporation, lc01707plf Datasheet - Page 18
![no-image](/images/manufacturer_photos/0/5/586/sanyo_semiconductor_corporation_sml.jpg)
lc01707plf
Manufacturer Part Number
lc01707plf
Description
Fm Multiple Tuner Ic
Manufacturer
Sanyo Semiconductor Corporation
Datasheet
1.LC01707PLF.pdf
(18 pages)
Continued from preceding page.
Register
20h
21h
22h
SD pin specification
SD voltage level
address
High level output voltage
Low level output voltage
BIT
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
This catalog provides information as of August, 2011. Specifications and information herein are subject
to change without notice.
SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using
products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition
ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd.
products described or contained herein.
SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all
semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or
malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise
to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt
safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not
limited to protective circuits and error prevention circuits for safe design, redundant design, and structural
design.
In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are
controlled under any of applicable local export control laws and regulations, such products may require the
export license from the authorities concerned in accordance with the above law.
No part of this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise,
without the prior written consent of SANYO Semiconductor Co.,Ltd.
Any and all information described or contained herein are subject to change without notice due to
product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the
SANYO Semiconductor Co.,Ltd. product that you intend to use.
Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed
for volume production.
Upon using the technical information or products described herein, neither warranty nor license shall be granted
with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third
party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's
intellctual property rights which has resulted from the use of the technical information and products mentioned
above.
ERR2
ERR1
DCOSEL2
DCOSEL1
DCOSEL0
DWAITSEL[1]
DWAITSEL[0]
DENINT
MASKSEL
LOSEL
INTPH
INTIM
INTLO
TESTSEL[2]
TESTSEL[1]
TESTSEL[0]
DSW
TIMESEL2[1]
TIMESEL2[0]
TIMESEL[1]
TIMESEL[0]
Bit name
V DD : supply voltage
item
Local oscillator capacitor bank control error flag 2
Local oscillator capacitor bank control error flag 1
Local oscillator capacitor bank value changeover
Local oscillator capacitor bank control process
changeover
Local oscillator capacitor bank control process
changeover (micro alignment)
PLL operation check wait time after local oscillator
capacitor bank adjustment
Register for TEST
Register for TEST
Register for TEST
Register for TEST
Register for TEST
Register for TEST
Register for TEST
Register for TEST
Register for TEST
PLL loop filter ON/OFF
Local oscillator capacitor bank control correcting circuit
operation clock setting
Local oscillator capacitor bank control sequential
comparison control operation clock setting
Function
LC01707PLF
min
1:cap bank control value 0:I
1:correcting process after sequential comparison
0:No correcting process after sequential comparison
1:micro adjustment process 0:No micro adjustment process
0:200μs 1: 400μs 2:800μs 3:1600μs
1:ON 0:OFF
0:200μs 1: 400μs 2:800μs 3:1600μs
0:10μs 1: 20μs 2:40μs 3:80μs
V DD -0.8
0
Bit operation
2
C input value
max
V DD
0.4
unit
V
V
Read/
Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
PS No.A1928-18/18
Binary
value
0
0
0
0
1
0
1
0
0
0
0
0
1
0
1
0
0
0
0
1
0
1
0
1
value
h’0A
h’0A
Hex
h’15