ltm9005v Linear Technology Corporation, ltm9005v Datasheet - Page 10
![no-image](/images/manufacturer_photos/0/3/389/linear_technology_corporation_sml.jpg)
ltm9005v
Manufacturer Part Number
ltm9005v
Description
Ltm9005 - If Sampling Receiver Subsystem
Manufacturer
Linear Technology Corporation
Datasheet
1.LTM9005V.pdf
(24 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ltm9005v-AA
Manufacturer:
LT
Quantity:
500
Company:
Part Number:
ltm9005v-AB
Manufacturer:
LT
Quantity:
500
Company:
Part Number:
ltm9005v-EXT
Manufacturer:
LT
Quantity:
425
LTM9005
pin FuncTions
D0 – D13 (See Table for Pin Locations): Digital Outputs.
D13 is the MSB.
OF (Pin G15): Over/Under Flow Output. High when an
over or under flow has occurred.
MODE (Pin F15): Output Format and Clock Duty Cycle
Stabilizer Selection Pin. Connecting MODE to GND selects
offset binary output format and turns the clock duty cycle
stabilizer off. 1/3 V
and turns the clock duty cycle stabilizer on. 2/3 V
2’s complement output format and turns the clock duty
cycle stabilizer on. V
format and turns the clock duty cycle stabilizer off.
SENSE (Pin H12): Reference Programming Pin. Connect-
ing SENSE to V
default input range. Connecting SENSE to 1.5V selects the
internal reference and a 3dB lower input range. An external
reference greater than 0.5V and less than 1V applied to
SENSE selects the external reference. A 1V external refer-
ence sets the input range equal to the default input range,
a 0.5V external reference sets the input range 3dB lower
and an external value between 0.5V and 1V sets the input
range proportionally.
A8 (Pin A8): Test Pin Used During Manufacturing Only.
Connect directly to B8. Keep this connection free from
noise.
A9 (Pin A9): Test Pin Used During Manufacturing Only.
Connect directly to B9. Keep this connection free from
noise.
B8 (Pin B8): Test Pin Used During Manufacturing Only.
Connect directly to A8. Keep this connection free from
noise.
B9 (Pin B9): Test Pin Used During Manufacturing Only.
Connect directly to A9. Keep this connection free from
noise.
10
DD
DD
selects the internal reference and the
DD
selects offset binary output format
selects 2’s complement output
DD
selects
L8 (Pin L8): Test Pin Used During Manufacturing Only.
Connect directly to M8. Keep this connection free from
noise.
L9 (Pin L9): Test Pin Used During Manufacturing Only.
Connect directly to M9. Keep this connection free from
noise.
M8 (Pin M8): Test Pin Used During Manufacturing Only.
Connect directly to L8. Keep this connection free from
noise.
M9 (Pin M9): Test Pin Used During Manufacturing Only.
Connect directly to L9. Keep this connection free from
noise.
OGND (Pins A16, A17, B17, C16 and C17): Output Driver
Ground.
OV
Drivers. This supply is internally bypassed to GND. OV
can be 0.5V to 3.6V.
V
V
V
Amplifier. V
at 3V if desired.
V
Amplifier. V
at 3V if desired.
V
V
desired.
GND (See Table for Pin Locations): Module Ground.
CC1
CC1
CC2
CC3
DD
DD
DD
(Pins A13 and B13): 3.3V Supply Voltage for ADC.
is internally bypassed to GND. Can operate at 3V if
(Pins M14 and M15): 3.3V Supply Voltage for Second
is internally bypassed to GND.
(Pins K1 and K2): 3.3V Supply Voltage for Mixer.
(Pins B1 and C1): 3.3V Supply Voltage for First
(Pins D16 and D17): Positive Supply for the Output
CC2
CC3
is internally bypassed to GND. Can operate
is internally bypassed to GND. Can operate
9005p
DD