mt8885an1 Zarlink Semiconductor, mt8885an1 Datasheet - Page 9
![no-image](/images/manufacturer_photos/0/7/727/zarlink_semiconductor_sml.jpg)
mt8885an1
Manufacturer Part Number
mt8885an1
Description
Integrated Dtmf Transceiver With Power-down And Adaptive Micro Interface
Manufacturer
Zarlink Semiconductor
Datasheet
1.MT8885AN1.pdf
(28 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MT8885AN1
Manufacturer:
ZARLINK
Quantity:
119
DTMF signals cannot be detected if CP mode has been selected (see Table 7). Figure 8 indicates the useful detect
bandwidth of the call progress filter. Frequencies presented to the input, which are within the ‘accept’ bandwidth
limits of the filter, are hard-limited by a high gain comparator with the IRQ/CP pin serving as the output. The
squarewave output obtained from the schmitt trigger can be analyzed by a microprocessor or counter arrangement
to determine the nature of the call progress tone being detected. Frequencies which are in the ‘reject’ area will not
be detected and consequently the IRQ/CP pin will remain low.
3.0
The DTMF transmitter employed in the MT8885 is capable of generating all sixteen standard DTMF tone pairs with
low distortion and high accuracy. All frequencies are derived from an external 3.579545 MHz crystal. The sinusoidal
waveforms for the individual tones are digitally synthesized by using row and column programmable dividers and
switched capacitor D/A converters. The row and column tones are mixed and filtered to provide a DTMF signal with
low total harmonic distortion and high accuracy. To specify a DTMF signal, data conforming to the encoding format
shown in Table 1 must be written to the transmit Data Register.
output code. The individual tones which are generated (f
Group tones. As seen from the table, the low group frequencies are 697, 770, 852 and 941 Hz. The high group
frequencies are 1209, 1336, 1477 and 1633 Hz. Typically, the high group to low group amplitude ratio (twist) is 2 dB
to compensate for high group attenuation on long loops.
The period of each tone consists of 32 equal time segments. The period of a tone is controlled by varying the length
of these time segments. During write operations to the Transmit Data Register the 4 bit data on the bus is latched
and converted to 2 of 8 coding for use by the programmable divider circuitry. This code is used to specify a time
segment length which will ultimately determine the frequency of the tone. When the divider reaches the appropriate
EXPLANATION OF EVENTS
A)
B)
C)
D)
E)
F)
EXPLANATION OF SYMBOLS
V
ESt
St/GT
RX
b3
b2
IRQ/CP
t
t
t
t
t
t
t
t
REC
REC
ID
DO
DP
DA
GTP
GTA
in
0
-RX
DTMF Generator
3
RETAINED UNTIL NEXT VALID TONE PAIR.
RETAINED UNTIL NEXT VALID TONE PAIR.
PRESENT/ABSENT FOR THE REQUIRED GUARD TIME THUS CONSTITUTING A VALID SIGNAL. ACTIVE LOW
FOR THE DURATION OF A VALID DTMF SIGNAL.
RECEIVE DATA REGISTER. THE BIT IS CLEARED AFTER THE STATUS REGISTER IS READ.
CLEARED AFTER THE STATUS REGISTER IS READ.
TONE BURSTS DETECTED, TONE DURATION INVALID, RX DATA REGISTER NOT UPDATED.
TONE #n DETECTED, TONE DURATION VALID, TONE DECODED AND LATCHED IN RX DATA REGISTER.
END OF TONE #n DETECTED, TONE ABSENT DURATION VALID, INFORMATION IN RX DATA REGISTER
TONE #n+1 DETECTED, TONE DURATION VALID, TONE DECODED AND LATCHED IN RX DATA REGISTER.
ACCEPTABLE DROPOUT OF TONE #n+1, TONE ABSENT DURATION INVALID, DATA REMAINS UNCHANGED.
END OF TONE #n+1 DETECTED, TONE ABSENT DURATION VALID, INFORMATION IN RX DATA REGISTER
DTMF COMPOSITE INPUT SIGNAL.
EARLY STEERING OUTPUT. INDICATES DETECTION OF VALID TONE FREQUENCIES.
STEERING INPUT/GUARD TIME OUTPUT. DRIVES EXTERNAL RC TIMING CIRCUIT.
4-BIT DECODED DATA IN RECEIVE DATA REGISTER
DELAYED STEERING IN STATUS REGISTER (BIT 3) INDICATES THAT VALID FREQUENCIES HAVE BEEN
RECEIVE DATA REGISTER FULL (BIT 2) IN STATUS REGISTER INDICATES THAT VALID DATA IS IN THE
INTERRUPT IS ACTIVE INDICATING THAT NEW DATA IS IN THE RX DATA REGISTER. THE INTERRUPT IS
MAXIMUM DTMF SIGNAL DURATION NOT DETECTED AS VALID. TYPICALLY 20 MS.
MINIMUM DTMF SIGNAL DURATION REQUIRED FOR VALID RECOGNITION. TYPICALLY 40 MS.
MINIMUM TIME BETWEEN VALID SEQUENTIAL DTMF SIGNALS. TYPICALLY 40 MS.
MAXIMUM ALLOWABLE DROPOUT DURING VALID DTMF SIGNAL. TYPICALLY 20 MS.
TIME TO DETECT VALID FREQUENCIES PRESENT.
TIME TO DETECT VALID FREQUENCIES ABSENT.
GUARD TIME, TONE PRESENT.
GUARD TIME, TONE ABSENT.
Figure 9 - Description of Timing Events
Zarlink Semiconductor Inc.
MT8885
9
LOW
and f
Note that Table 1 is the same as the receiver
HIGH
) are referred to as Low Group and High
Data Sheet