ftlx1341e2 Finisar Corporation., ftlx1341e2 Datasheet
ftlx1341e2
Related parts for ftlx1341e2
ftlx1341e2 Summary of contents
Page 1
... De-latch mechanism with low extraction force The Finisar FTLX1341E2 transponder incorporates Electronic Dispersion Compensation (EDC) which provides correction for the severe modal dispersion that may occur during propagation through links up to 220m on legacy installed FDDI multimode fiber. The EDC device incorporates a Feed Forward Equalizer (FFE) and a Decision Feedback Equalizer (DFE) ...
Page 2
... FTLX1341E2 Product Specification – October 2008 I. Pin Description Signal Name Level Management and Monitoring Ports MDIO Open Drain (output) 1.2V CMOS (input) MDC 1.2 V CMOS PRTAD4 1.2 V CMOS PRTAD3 1.2 V CMOS PRTAD2 1.2 V CMOS PRTAD1 1.2 V CMOS PRTAD0 1.2 V CMOS LASI Open Drain RESET 1.2 V CMOS Vendor Specific TX ON/OFF 1 ...
Page 3
... FTLX1341E2 Product Specification – October 2008 Receive Functions Reserved Reserved RX LANE 0+ AC-coupled, RX LANE 0– Internally biased differential RX LANE 1+ XAUI RX LANE 1– RX LANE 2+ RX LANE 2– RX LANE 3+ RX LANE 3– DC Power GND APS +1.2 V APS SENSE +1.2 V APS SET 3 5 Reserved Reserved © ...
Page 4
... FTLX1341E2 Product Specification – October 2008 Electrical Pad Layout Absolute Maximum Ratings II. Parameter Storage Temperature 1) Supply Voltage +5.0 V Supply Voltage +3.3 V Supply Voltage APS Static Discharge Voltage, All Pins Average Receive Optical Power Notes: 1) Non-condensing 2) HBM Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. ...
Page 5
... FTLX1341E2 Product Specification – October 2008 III. Electrical Characteristics Recommended Operating Conditions Parameter Operating Case Temperature Transponder Total Power Consumption Supply Voltage +5.0 V Supply Current +5.0 V Supply Voltage +3.3 V Supply Current +3.3 V Supply Voltage APS Supply Current APS 1) Measured at reference thermal location, see Figure 3. See also Environmental Performance. ...
Page 6
... FTLX1341E2 Product Specification – October 2008 Electrical AC Characteristics ( CC5 Parameter XAUI Input AC Characteristics (TXLANE[0..3]) Baud Rate Ethernet Baud Rate Tolerance Differential Input Impedance 1) Differential Return Loss 2) Input Differential Skew Jitter Amplitude Tolerance XAUI Output AC Characteristics (RXLANE[0..3]) Baud Rate Ethernet ...
Page 7
... FTLX1341E2 Product Specification – October 2008 Optical Specifications Parameter Transmitter Optical Modulation Amplitude (OMA) Average Launch Power Peak Launch Power Optical Wavelength Spectral Width Optical Extinction Ratio Optical Eye Mask Margin Transmitter Waveform Dispersion Penalty Average Launch Power of OFF Transmitter Uncorrelated Jitter [rms] ...
Page 8
... FTLX1341E2 Product Specification – October 2008 Environmental Performance Operating case temperature: Operating humidity: Fibers and Connectors The transponder has SC receptacles for both Tx and Rx. The transponder is designed for multimode SC cables, 0° polished endface (PC). 70-pin Connector The module interface connector is a 70-pin, printed circuit board edge connection with a 0.5 mm pitch ...
Page 9
... FTLX1341E2 Product Specification – October 2008 Eye Safety Finisar FTLX1341E2 transponders are Class 1 Laser Products. They are certified per the following standards: Feature Agency Laser Eye FDA/CDRH CDRH 21 CFR 1040 and Laser Notice 50 Safety Laser Eye Safety TÜV Electrical TÜV Safety ...
Page 10
... FTLX1341E2 Product Specification – October 2008 Package Outline IX. References The following references are provided for informational purposes only. The parameters and operational behavior outlined in this specification describe the complete functionality of the 10G Transponder. Contact Finisar for any items concerning the operational characteristics of this device. ...