ftlf1421p1xtl Finisar Corporation., ftlf1421p1xtl Datasheet
ftlf1421p1xtl
Related parts for ftlf1421p1xtl
ftlf1421p1xtl Summary of contents
Page 1
... Low power dissipation <700mW typical • Industrial operating temperature range: -40°C to 85°C Finisar’s FTLF1421P1xTL Small Form Factor Pluggable (SFP) transceivers are compatible with the Small Form Factor Pluggable Multi-Sourcing Agreement (MSA) They comply with SONET OC-48 IR-1 (SDH STM S-16.1) standards as specified in IEEE Std 802.3 SONET OC-12 and SONET OC-3 standards via the 2-wire serial bus specified in the SFP MSA ...
Page 2
... FTLF1421P1xTL Pluggable SFP Product Specification – December 2005 I. Pin Descriptions Pin Symbol 1 V Transmitter Ground (Common with Receiver Ground) EET 2 T Transmitter Fault. Not supported. FAULT 3 T Transmitter Disable. Laser output disabled on high or open. DIS 4 MOD_DEF(2) Module Definition 2. Data line for Serial ID. ...
Page 3
... FTLF1421P1xTL Pluggable SFP Product Specification – December 2005 II. Absolute Maximum Ratings Parameter Maximum Supply Voltage Storage Temperature Case Operating Temperature Relative Humidity III. Electrical Characteristics Parameter Supply Voltage Supply Current Transmitter Input differential impedance Single ended data input swing Transmit Disable Voltage ...
Page 4
... FTLF1421P1xTL Pluggable SFP Product Specification – December 2005 IV. Optical Characteristics Parameter Transmitter Output Opt. Pwr: 9/125 SMF Optical Wavelength Spectral Width –20dB Optical Extinction Ratio Sidemode Supression ratio Optical Rise/Fall Time Relative Intensity Noise Total Generated Transmitter Jitter (peak to peak) Total Generated Transmitter Jitter ...
Page 5
... FTLF1421P1xTL Pluggable SFP Product Specification – December 2005 V. General Specifications Parameter Data Rate Bit Error Rate @ OC-48 Max. Supported Link Length on 9/125µm SMF @ OC-48 Max. Supported Link Length on 9/125µm SMF @ 2X Fibre Channel Max. Supported Link Length on 9/125µm SMF @ Gigabit Ethernet Max. Supported Link Length on 9/125µ ...
Page 6
... For more information, please see the SFP MSA documentation Note AN-2030. Digital diagnostics for the FTLF1421P1xTL are externally calibrated by default. Please note that evaluation board FDB-1018 is available with Finisar ModDEMO software that allows simple to use communication over the 2-wire serial interface. ...
Page 7
... FTLF1421P1xTL Pluggable SFP Product Specification – December 2005 IX. Mechanical Specifications Finisar’s Small Form Factor Pluggable (SFP) transceivers are compatible with the dimensions defined by the SFP Multi-Sourcing Agreement (MSA) Finisar Corporation December 2, 2005 Rev A FTLF1421P1BTL Page 7 ...
Page 8
... FTLF1421P1xTL Pluggable SFP Product Specification – December 2005 Finisar Corporation December 2, 2005 Rev A FTLF1421P1WTL Page 8 ...
Page 9
... FTLF1421P1xTL Pluggable SFP Product Specification – December 2005 X. PCB Layout and Bezel Recommendations Finisar Corporation December 2, 2005 Rev Page 9 ...
Page 10
... FTLF1421P1xTL Pluggable SFP Product Specification – December 2005 Finisar Corporation December 2, 2005 Rev Page 10 ...
Page 11
... January 27, 2003. (*) Neither IEEE 802.3 nor FC-PI 13.0 specifies a 1310nm DFB single mode interface. The FTLF1421P1xTL complies with these standards except for receiver sensitivity, and transmit output power. See Section IV for details. XII. ...