xe0046 ETC-unknow, xe0046 Datasheet

no-image

xe0046

Manufacturer Part Number
xe0046
Description
High-performance Quad Module
Manufacturer
ETC-unknow
Datasheet
Description
Xecom created the XE0046 for high-performance,
multi-line applications. The XE0046 integrates
four high performance DAA's into a single
compact module. Each DAA circuit operates
independently of all the others.
Like all of Xecom's DAA modules, the XE00046
integrates a Ring Detect Circuit, Loop Current
Holding Circuit, Solid-State Hookswitch, and
Telephone Line Transformer for each line. The
XE0046 also provides each line with a path for
the Caller ID signal from the telephone network
and a two-to-four wire convertor. The two-to-four
wire convertor separates the receive signal from
the transmit signal.
Below is a list of the special features incorporated
into the XE0046 for high-performance, multi-line
applications.
XE0046 Block Diagram
XECOM
OH
RX
TX
RI
Convertor
2/4 Wire
High-Performance Quad DAA Module
(This Block Diagram represents each DAA within the XE0046)
Transformer
Line
XE0046 Features
* Four Individual DAA's in a Single Package;
* Each DAA supports 33,600 bps data transfer;
* Each DAA provides a path for the Caller ID
* Each DAA includes a 2/4 four wire convertor;
* Each DAA passes network signaling up to 0
* Small Size: 2.5 inches long, 1.5 inches wide,
* FCC Part 68 Compliant;
* Individual Ring Detection for each line;
* Each DAA integrates a Low-Distortion
* Each DAA provides a1500 volts isolation
* Solid-State Hookswitch Control for each line;
Line Current
signal from the phone company central office;
dBm without distortion.
and 0.6 inches high;
Telephone Line Transformer;
between the phone line and all other circuits;
Caller ID
Holding
Circuit
Hookswitch
Detector
Ring
XE0046
XE0046
Tip
Ring
02/98

Related parts for xe0046

xe0046 Summary of contents

Page 1

... Each DAA integrates a Low-Distortion Telephone Line Transformer; * Each DAA provides a1500 volts isolation between the phone line and all other circuits; * Solid-State Hookswitch Control for each line; (This Block Diagram represents each DAA within the XE0046) Caller ID Line Current Line Holding ...

Page 2

... Notes: These dimensions reflect the module's maximum envelope. I/O pins are .025 inch square, tin-plated. J Warning: There are un-insulated electrical con- ductors on the underside of the XE0046 exposed electrical conductors should be routed under the module XE0046 Pin Configuration ...

Page 3

... XE0046 Signal Descriptions Pin Name Description 1 VCC VCC provides the + 5 volt power source for the XE0046. 2 Vdd Vdd provides the -5 volt power source to the XE0046 4, 8, 10, 16 Tip(n) Tip provides the second connection to the telephone network (RJ11 Pin 3) on each of the four internal DAAs. Tip has 1500 volts isolation from the rest of the circuitry ...

Page 4

... Caller ID Insertion Loss Hookswitch open XECOM (Vcc = +5 Volts ±10%, Vdd = -5 Volts ±10%,Ta deg C) Conditions (4) Min Typ Max Units -1.0 0 1.0 dB -1.0 0 1.0 dB 540 600 660 Ohms 38 150 Vrms 100 0.2 0.5 Volts 2.0 3.0 Volts 0.2 0.5 Volts 100 mA -85 dBm -8.0 -6.0 -4.0 dBm XE0046 ...

Page 5

... If the system is capable of DTMF dialing, the maximum DTMF transmission level must be less than 0 dBm averaged over a 3 second interval. 4. Billing Delay A delay of 2 seconds or greater is required after the time the XE0046 is taken “off hook” and before any information is transmitted. This is required to ensure that billing information may be exchanged between telephone company central offices without interference. ...

Page 6

... Xecom reserves the right to modify specifications and/or prices without notice. Product mentioned herein are used for identification purposes only and may be trademarks and/or registered trademarks of their respective companies. XECOM Xecom Incorporated 374 Turquoise Street, Milpitas, CA 95035 Ph:408 -945 -66 40 Fax: 408 - 942-1346 E-Mail info@xecom.com XE0046 ...

Related keywords