hys64d32020hdl-5-c Infineon Technologies Corporation, hys64d32020hdl-5-c Datasheet - Page 20
![no-image](/images/no-image-200.jpg)
hys64d32020hdl-5-c
Manufacturer Part Number
hys64d32020hdl-5-c
Description
200-pin Small Outline Dual-in-line Memory Modules
Manufacturer
Infineon Technologies Corporation
Datasheet
1.HYS64D32020HDL-5-C.pdf
(30 pages)
Table 12
Parameter
Address and control input hold
time
Read preamble
Read postamble
Active to Precharge command
Active to Active/Auto-refresh
command period
Auto-refresh to Active/Auto-
refresh command period
Active to Read or Write delay
Precharge command period
Active to Autoprecharge delay
Active bank A to Active bank B
command
Write recovery time
Auto precharge write recovery +
precharge time
Internal write to read command
delay
Exit self-refresh to non-read
command
Exit self-refresh to read
command
Average Periodic Refresh
Interval
1) 0 C
2) Input slew rate 1 V/ns for DDR400, DDR333
3) The CK/CK input reference level (for timing reference to CK/CK) is the point at which CK and CK cross: the input reference
4) Inputs are not recognized as valid until
5) The Output timing reference level, as measured at the timing reference point indicated in AC Characteristics (note 3) is
6) These parameters guarantee device timing, but they are not necessarily tested on each device.
7)
8) The specific requirement is that DQS be valid (HIGH, LOW, or some point on a valid transition) on or before this CK edge.
9) The maximum limit for this parameter is not a device limit. The device operates with a greater value for this parameter, but
Data Sheet
(DDR400)
level for signals other than CK/CK, is
t
to a specific voltage level, but specify when the device is no longer driving (HZ), or begins driving (LZ).
A valid transition is defined as monotonic and meeting the input slew rate specifications of the device. When no writes were
previously in progress on the bus, DQS will be transitioning from Hi-Z to logic LOW. If a previous write was in progress,
DQS could be HIGH, LOW, or transitioning from HIGH to LOW at this time, depending on
system performance (bus turnaround) degrades accordingly.
HZ
and
T
t
A
LZ
AC Timing - Absolute Specifications for DDR400B and DDR333 (cont’d)
70 C
transitions occur in the same access time windows as valid data transitions. These parameters are not referred
; V
DDQ
= 2.5 V 0.2 V,
Symbol
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
IH
RPRE
RPST
RAS
RC
RFC
RCD
RP
RAP
RRD
WR
DAL
WTR
XSNR
XSRD
REFI
V
REF
V
REF
V
. CK/CK slew rate are 1.0 V/ns.
DD
stabilizes.
= +2.5 V 0.2 V (DDR333);
Min.
0.6
0.7
0.9
0.40
40
55
65
15
15
t
10
15
2
75
200
—
RCD
—
DDR400B
or t
–5
Max.
—
—
1.1
0.60
70E+3
—
—
—
—
—
—
—
—
—
7.8
RASmin
20
—
HYS64D[32020/16000][H/G]DL–[5/6]–C
Min.
0.75
0.8
0.9
0.40
42
60
72
18
18
t
12
15
1
75
200
—
RCD
Small Outline DDR SDRAM Modules
—
DDR333
or t
–6
Max.
—
—
1.1
0.60
70E+3
—
—
—
—
—
—
—
—
—
7.8
V
RASmin
DDQ
—
= 2.6 V 0.1 V,
Unit
ns
ns
t
t
ns
ns
ns
ns
ns
ns
ns
ns
t
t
ns
t
s
CK
CK
CK
CK
CK
t
DQSS
Electrical Characteristics
.
Note/ Test
Condition
fast slew rate
3)4)5)6)10)
slow slew rate
3)4)5)6)10)
2)3)4)5)
2)3)4)5)
2)3)4)5)
2)3)4)5)
2)3)4)5)
2)3)4)5)
2)3)4)5)
2)3)4)5)
2)3)4)5)
2)3)4)5)
2)3)4)5)11)
2)3)4)5)
2)3)4)5)
2)3)4)5)
2)3)4)5)12)
V
DD
Rev. 1.0, 2004-03
= +2.6 V 0.1 V
1)
V
TT
.