atr0630p1 ATMEL Corporation, atr0630p1 Datasheet
atr0630p1
Related parts for atr0630p1
atr0630p1 Summary of contents
Page 1
... Up to 4Hz Update Rate • Supports A-GPS (Aiding) • Excellent Noise Performance ® Processor Core ANTARIS4 Single-chip GPS Receiver ATR0630P1 Automotive Summary NOTE: This is a summary document. The complete document is available. For more information, please contact your local Atmel sales office. 4978AS–GPS–12/07 ...
Page 2
... Due to the integrated ARM7TDMI processor and an intelligent radio architecture, the ATR0630P1 operates in a complete autonomous mode, utilizing on chip AGC in closed loop operation. For maximum performance, we recommend to use the ATR0630P1 together with a low noise amplifier (e.g. ATR0610). The ATR0630P1 supports assisted GPS. ATR0630P1 2 ® ...
Page 3
... Architectural Overview 2.1 Block Diagram Figure 2-1. ATR0630P1 Block Diagram PUXTO PURF VDD18 VDDIO VDD_USB VDIG VCC1 VCC2 VBP TEST MO RF NRF XTO NXTO X NX RF_ON NSHDN NSLEEP XT_IN XT_OUT P20/TIMEPULSE P29/GPSMODE12 P27/GPSMODE11 P26/GPSMODE10 P24/GPSMODE8 P23/GPSMODE7 P19/GPSMODE6 P17/GPSMODE5 P13/GPSMODE3 P12/GPSMODE2 P1/GPSMODE0 P14/NAADET1 P25/NAADET0 ...
Page 4
... Especially, due to its fast search engine and GPS accelerator, the ATR0630P1 only needs a GPS crystal (XTAL resonator for the integrated crystal oscillator of the ATR0630P1. This saves the considerable higher cost of a TCXO which is required for competitor’s systems. Also, as the powerful standard software is available in ROM, no external flash memory is needed ...
Page 5
... The ARM standard In-Circuit Emulation debug interface is supported via the JTAG/ICE port of the ATR0630P1. The ATR0630P1 architecture consists of two main buses, the Advanced System Bus (ASB) and the Advanced Peripheral Bus (APB). The ASB is designed for maximum performance. It inter- faces the processor with the on-chip 32-bit memories and the external memories and devices by means of the External Bus Interface (EBI) ...
Page 6
... Pin Configuration 3.1 Pinout Figure 3-1. Pinning BGA96 (Top View Table 3-1. ATR0630P1 Pinout Pin Name BGA 96 Pin Type AGCO A4 Analog I/O CLK23 A8 Digital OUT DBG_EN E8 Digital IN EGC D4 Digital IN GDIG C5 Supply GND A6 Supply GND A9 Supply GND B11 Supply GND F5 Supply GND ...
Page 7
... Table 3-1. ATR0630P1 Pinout (Continued) Pin Name BGA 96 Pin Type GNDA B4 Supply GNDA D2 Supply GNDA E1 Supply GNDA E2 Supply GNDA E3 Supply GNDA F1 Supply GNDA F2 Supply GNDA F3 Supply GNDA G1 Supply GNDA H1 Supply LDOBAT_IN D11 Supply LDO_EN C11 Digital IN LDO_IN E11 Supply LDO_OUT E12 Supply ...
Page 8
... Table 3-1. ATR0630P1 Pinout (Continued) Pin Name BGA 96 Pin Type P20 G7 Digital I/O P21 E6 Digital I/O P22 D10 Digital I/O P23 F8 Digital I/O P24 H7 Digital I/O P25 G5 Digital I/O P26 B6 Digital I/O P27 F7 Digital I/O P28 E7 Digital I/O P29 D5 Digital I/O P30 G12 Digital I/O P31 C10 Digital I/O PURF G4 Digital IN PURF H4 Digital IN PUXTO ...
Page 9
... Table 3-1. ATR0630P1 Pinout (Continued) Pin Name BGA 96 Pin Type (3) VDD_USB A10 Supply VDD18 H9 Supply VDD18 G11 Supply VDD18 F12 Supply VDD18 B9 Supply VDD18 E5 Supply (4) VDDIO B5 Supply VDDIO H5 Supply VDIG A5 Supply X A2 Analog OUT XT_IN A12 Analog IN XT_OUT B12 Analog OUT XTO ...
Page 10
... DIGITAL IN 2 F[6-8], H[6,7] G8 NEEPROM DIGITAL IN GPS D7 STATUSLED DIGITAL OUT G7 TIMEPULSE DIGITAL OUT ATR0630P1 10 Type Active Level Pin Description/Comment - Leave open, internal pull down Low Reset input; open drain with internal pull-up resistor Low Shutdown output, connect to LDO_EN (C11) - Enable LDO18 Low Power-up output for GPS XTAL, connect to PUXTO (F4) ...
Page 11
... Digital IF (sample clock) - Analog supply 3V - Analog supply 3V - Analog supply 3V - Analog Ground - Digital supply (radio) 1.8V - Core voltage 1.8V USB transceiver supply voltage (3.0V to 3.6V (USB enabled 2.0V (USB disabled)) - Variable I/O voltage 1.65V to 3.6V - Digital ground (radio) - Digital ground - 2.3V to 3.6V - 1.8V LDO18 output, max 2.3V to 3.6V - 1.5V to 3.6V - 1.8V LDOBAT Output ATR0630P1 11 ...
Page 12
... External Connections for a Working GPS System Figure 3-2. Example of an External Connection (ATR0630P1) LNA (optional) SAW ATR0610 GND +3V (see Power Supply) (see Power Supply) GND NC: Not connected ATR0630P1 12 ATR0630P1 NC SIGHI NC SIGLO NC CLK23 RF NRF RF_ON PURF NSLEEP PUXTO NC NRESET NC TMS NC TCK NC TDI NC NTRST ...
Page 13
... MPQ BGA96 3000 - 0.08 C and seating plane are defined by the spherical crowns of the solder balls C ATR0630P1 Remarks mm, 0.8 mm pitch, Pb-free, RoHS-compliant Evaluation kit/Road test kit Design kit including design guide and PCB Gerber files 2. m 0.08 C 0.4 ±0.05 0.15 ...
Page 14
... Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. © 2007, Atmel Corporation. All rights reserved. Atmel of Atmel Corporation or its subsidiaries. ARM Ltd ...