gpm140 SL Power Electronics, gpm140 Datasheet

gpm140

Manufacturer Part Number

gpm140

Description

Gpm140 Global Performance Switchers

Manufacturer

SL Power Electronics

Datasheet

1.GPM140.pdf (2 pages)

Available stocks

Company

Part Number

Manufacturer

Quantity

Price

Company:

Bonase Electronics (HK) Co., Limited

Part Number:

gpm140-12

Manufacturer:

SLPOWER

Quantity:

500

Company:

Bonase Electronics (HK) Co., Limited

Part Number:

gpm140-12TG

Manufacturer:

SLPOWER

Quantity:

500

Company:

Bonase Electronics (HK) Co., Limited

Part Number:

gpm140-15

Manufacturer:

SLPOWER

Quantity:

500

Company:

Bonase Electronics (HK) Co., Limited

Part Number:

gpm140-24

Manufacturer:

SLPOWER

Quantity:

500

Company:

Bonase Electronics (HK) Co., Limited

Part Number:

gpm140-24G

Manufacturer:

SLPOWER

Quantity:

500

Current page: 1 of 2
Download datasheet (43Kb)

GPM140 GLOBAL PERFORMANCE SWITCHERS

SPECIFICATIONS:

AC Input

85-264Vac, 47-63Hz single phase.

Input Current

Maximum input current at 120Vac, 60Hz with full rated output load: 3.7A

Hold-Up Time

20mSec minimum from loss of AC input at full load, nominal line (115Vac).

Output Power

140W convection, 160W with 26cfm moving air. Peak ratings are for 60

sec. maximum duration, 10% duty cycle.

Overload Protection

Fully protected against short circuit and output overload. Short circuit

protection is cycling type power limit. See output ratings chart for

additional notes or conditions.

Overvoltage Protection

Main outputs: 124%

Efficiency

65% at full rated load, nominal input voltage, depending on model and

load distribution.

Turn-on Time

Less than 1 second at 120Vac, 25 C (inversely proportional to input

voltage and thermistor temperature).

Input Protection

Internal AC fuse provided. Designed to blow only if a catastrophic failure

occurs in the unit.

Inrush Current

Inrush is limited by internal thermistors. Inrush at 240Vac under cold start

conditions will not exceed 60A.

Temperature Coefficient

0.03%/ºC typical on all outputs.

Environmental

Designed for 0 to 50 C operation at full rated output power; derate

output current and total output power by 2.5% per C above 50 C. See

Environmental and Packaging Specifications (p. 11) for additional

information.

Power Fail

TTL- or CMOS-compatible output goes low (< 0.5V) 5mSec before

output voltage drops more than 4% below nominal voltage upon loss of

AC power. The signal is factory set to trip on 84 to 94Vac brown-out

depending upon incoming line impedance and distortion. Other settings

are available to the user through adjustment of built-in potentiometer

(consult factory for assistance).

No-Load Turn-on/Standby

No degradation of reliability will occur.

2311 Statham Parkway, Oxnard, CA 93033 • 800-235-5929 • 805-486-4565 • FAX 805-487-8911 • www.condorpower.com/

Condor D.C. Power Supplies, Inc./A subsidiary of SL Industries, Inc.

12%

FEATURES:

• Wide-range AC input 85-264Vac

• 2-year warranty

• Approved to UL2601-1, IEC601-1 and CSA22.2 No. 601

• Exceeds FCC and VDE/CISPR11 Class B/IEC601-1-2

• For commercial version, see p. 28

•

Output Noise

0.5% RMS, 1% Pk-Pk, 20MHz bandwidth, differential mode. Measured

with noise probe directly across output terminals of the power supply.

Transient Response

Main output—500 Sec typical response time for return to within 0.5% of

final value for a 50% load step change. i/ t<0.2A/ Sec. Maximum

voltage deviation is 3.5%. Startup/shutdown overshoot less than 3%.

Remote Sense

Provided as a standard feature on single-output models.

Voltage Adjustment

Built-in potentiometer adjusts voltage 5%.

Reverse Voltage Protection

All outputs protected against inadvertent application of reverse voltage up

to 1 times rated current of the reverse output.

Overload Protection

Factory set to begin power limiting at approximately 175W.

EMI/EMC Compliance

All models include built-in EMI filtering to meet the following emissions

requirements:

Leakage Current

60 A. 254Vac @ 60Hz input.

Safety

Approved to UL2601, CSA22.2 No. 601 Level 3 and IEC601. UL file

E116994; CSA #LR46516. The output(s) are intended for safety earthed

Signal Output and Intermediate Circuits only. The output(s) are not

acceptable for patient connection without additional isolation. All DC

outputs are SELV under normal and single fault conditions.

EMI SPECIFICATIONS

Conducted Emissions

Static Discharge

RF Field Susceptibility

Fast Transients/Bursts

Surge Susceptibility

marked to LVD

COMPLIANCE LEVEL

EN55011 Class B; FCC Class B

EN61000-4-2, 6 kV contact, 8 kV air

EN61000-4-3, 3 V/meter

EN61000-4-4, 2 kV, 5 kHz

EN61000-4-5, 1 kV diff., 2 kV com.

Related parts for gpm140

gpm140 Summary of contents

Page 1

... GPM140 GLOBAL PERFORMANCE SWITCHERS SPECIFICATIONS: AC Input 85-264Vac, 47-63Hz single phase. Input Current Maximum input current at 120Vac, 60Hz with full rated output load: 3.7A Hold-Up Time 20mSec minimum from loss of AC input at full load, nominal line (115Vac). Output Power 140W convection, 160W with 26cfm moving air. Peak ratings are for 60 sec ...

Page 2

... A A. Total regulation is defined as the maximum deviation from the nominal voltage for all steady-state conditions of initial voltage setting, input line voltage and output load. B. Unrestricted natural convection cooling. C. Requires 26cfm moving air. GPM140 MECHANICAL SPECIFICATIONS: INPUT: J1: AMP P.C.B. HEADER P/N 640445-5 PIN 1) AC LINE ...

Related keywords

gpm140 datasheet
gpm140 data sheet
gpm140 pdf datasheet
gpm140 component
gpm140 part
gpm140 distributor
gpm140 RoHS
gpm140 datasheet download