VDIP1_10 FTDI [Future Technology Devices International Ltd.], VDIP1_10 Datasheet
VDIP1_10
Related parts for VDIP1_10
VDIP1_10 Summary of contents
Page 1
Future Technology Devices International Ltd. Vinculum VNC1L Module Future Technology Devices International Ltd (FTDI) Unit 1, 2 Seaward Place, Centurion Business Park, Glasgow, G41 1HH, United Kingdom Tel.: +44 (0) 141 429 2777 E-Mail (Support): Neither the whole nor any ...
Page 2
Introduction The VDIP1 module is an MCU to embedded USB host controller development module for the VNC1L IC device. The VDIP1 is supplied on a PCB designed to fit into a 24 pin DIP socket, and provides access ...
Page 3
Introduction .................................................................... 1 2 Features .......................................................................... 3 3 Pin Out and Signal Description ........................................ 4 3.1 Module Pin Out .......................................................................... 4 3.2 Pin Signal Description ............................................................... 5 3.3 I/O Configuration Using The Jumper Pin Header ...................... 6 3.4 ...
Page 4
Features The VDIP1 has the following features Uses FTDI’s VNC1L embedded dual USB host controller IC device USB single ‘A’ type USB socket to interface with USB peripheral devices Second USB interface port available via module pins if ...
Page 5
Pin Out and Signal Description 3.1 Module Pin Out Figure 3.1 - VDIP1 Module Pin Out (Top View) Copyright © 2010 Future Technology Devices International Limited Document Reference No.: FT_000016 VDIP1 Vinculum VNC1L Module Datasheet Version 1.01 Clearance ...
Page 6
Pin Signal Description Pin No. Name Pin Name on PCB 1 5V0 5V0 2 LED1 LD1 3 LED2 LD2 4 USBD1P U1P 5 USBD1M U1M 6 ADBUS0 AD0 7 GND GND 8 ADBUS1 AD1 9 ADBUS2 AD2 10 ...
Page 7
I/O Configuration Using The Jumper Pin Header Two three way jumper pin headers are provided to allow for simple configuration of the I/O on data and control bus pins of the VDIP1. This is done by a combination ...
Page 8
Default Interface I/O Pin Configuration The VNC1L device is pre-programmed with default settings for the I/O pins however they can be easily changed to suit a designers needs. The default interface I/O pin configuration of the VNC1L device ...
Page 9
Signal Descriptions - UART Interface The UART interface I/O pin description of the VNC1L device are shown in Pin No. Name 6 TXD Output 8 RXD Input 9 RTS# Output 10 CTS# Input 11 DTR# Output 12 DSR# ...
Page 10
Signal Descriptions – Serial Peripheral Interface (SPI) The SPI I/O pin description of the VNC1L device are shown in Pins Table 3.5 - Data and Control Bus Signal Mode Options – SPI Slave ...
Page 11
SPI Slave Data Write Cycle When in SPI mode, the timing of a write operation is shown in Figure 3.4 – SPI Slave Data Write Cycle. From Start - SPI CS must be held high for the entire ...
Page 12
SPI Slave Data Timing Diagrams Figure 3.5 – SPI Slave Data Timing Diagrams. Time Description T1 SPICLK Period T2 SPICLK High T3 SPICLK Low T4 Input Setup Time T5 Input Hold Time T6 Output Hold Time T7 Output ...
Page 13
Signal Descriptions - Parallel FIFO Interface The Parallel FIFO interface I/O pin description of the VNC1L device is shown in Pin No. Name I/O ...
Page 14
Timing Diagram – Parallel FIFO Read Transaction When in parallel FIFO interface mode, the timing of a read is shown in Figure 3.6 and Table 3.9 Figure 3.6 - FIFO Read Cycle. Time Description T1 RD# Active Pulse ...
Page 15
Timing Diagram - Parallel FIFO Write Transaction When in parallel FIFO interface mode, the timing of a write operation is shown in Figure 3.7 and Table 3.10 Figure 3.7 - FIFO Write Cycle. Time Description T7 WR Active ...
Page 16
Firmware 4.1.1 Firmware Support There are currently 6 standard firmware versions available for from the FTDI website. VDAP Firmware: USB Host for single Flash Disk and General Purpose USB peripherals. Selectable UART, FIFO or SPI interface command monitor. ...
Page 17
Mechanical Dimensions Figure 5.1 VDIP1 Dimensions (Top View) Figure 5.2 VDIP1 Dimensions (Side View) Copyright © 2010 Future Technology Devices International Limited Document Reference No.: FT_000016 VDIP1 Vinculum VNC1L Module Datasheet Version 1.01 Clearance No.: FTDI# 131 16 ...
Page 18
External circuit Configuration 6.1 Adding a second USB Port The external circuit configuration for adding second USB host port, with the USB activity LED, is shown below in Figure 6.1 Figure 6.1 Additional USB Port Configuration Copyright © ...
Page 19
Schematic Diagram Figure 7.1 - Schematic Diagram Copyright © 2010 Future Technology Devices International Limited Document Reference No.: FT_000016 VDIP1 Vinculum VNC1L Module Datasheet Version 1.01 Clearance No.: FTDI# 131 18 ...
Page 20
Contact Information Head Office – Glasgow, UK Future Technology Devices International Limited Unit 1, 2 Seaward Place, Centurion Business Park Glasgow, G41 1HH United Kingdom Tel: +44 (0) 141 429 2777 Fax: +44 (0) 141 429 2758 E-mail ...
Page 21
Appendix A – References http://www.vinculum.com/documents/fwspecs/UM_VinculumFirmware_V205.pdf Copyright © 2010 Future Technology Devices International Limited Document Reference No.: FT_000016 VDIP1 Vinculum VNC1L Module Datasheet Version 1.01 Clearance No.: FTDI# 131 20 ...
Page 22
Appendix B – List of Figures and Tables List of Figures Figure 1.1- VDIP1 ......................................................................................................................... 1 Figure 3.1 - VDIP1 Module Pin Out (Top View) .................................................................................. 4 Figure 3.2 – VDIP1 On-Board Jumper Pin Configuration. ................................................................... 6 Figure 3.3 ...
Page 23
Appendix C – Revision History Version 0.91 Initial Datasheet Created Version 0.92 Datasheet Updated Version 1.0 Datasheet Updated (Reformatted) Datasheet Updated (Mechanical Drawings) Added Appendix A Added schematic Version 1.01 Corrected Table 3.1 (pin 18, 19, 20, 21) Copyright ...